The authors thank Dr. Dario Bonetta for providing Arabidopsis thaliana seeds and for technical assistance in regards to the triple response assay, as well as Simone Quaranta for help with FT-IR. This work was supported by a Natural Sciences and Engineering Research Council of Canada Discovery Grant (NSERC-DG) to JLS, an Ontario Graduate Scholarship (OGS) to RVA, and a Queen Elizabeth II Graduate Scholarship in Science and Technology (QEII-GSST) to AJV.

1. Chemicals
<ol>
	<li>Prepare a solution of 500 mM CEPA (144.49 g/mol), and a solution consisting of both 500 mM NaCl (58.44 g/mol) and 500 mM NaH2PO4&#183;H2O (137.99 g/mol) in acidified (pH 2.5) ultra-pure water or 0.1 N HCl. Mix using a vortex until the solutions are clear.</li>
	<li>Serially dilute (10x) the 500 mM solutions in the same solvent to obtain 5 mM and 50 mM stocks.</li>
	<li>Prepare a 10 mM solution of 1-aminocyclopropane carboxylic acid (ACC; 101.1 g/mol) in ultra-pure water.</li>
	<li>Filter-sterilize stock solutions and store aliquots at -20 &#176;C.</li>
	<li>Filter-sterilize cellulase. Store aliquots at 4 &#176;C.</li>
</ol>
2. Verifying Ethylene Production from 2-Chloroethylphosphonic Acid Decomposition: Triple Response Assay
<ol>
	<li>Surface-sterilize Arabidopsis thaliana Ecotype Columbia Seeds Using the Vapor-phase Method: 
	CAUTION: The following step produces toxic chlorine gas. Conduct seed sterilization in a fume hood.
	<ol>
		<li>Obtain a sealable container deep enough to accommodate a 250 ml glass beaker for seed sterilization and place it in a fume hood.</li>
		<li>Add A. thaliana seeds to a microcentrifuge tube and place the tube in a rack. Place the rack containing the open tube into the sealable container. 
		Note: Do not fill individual tubes over half full to allow chlorine gas to penetrate the lower seeds.</li>
		<li>Place a 250 ml beaker containing 100 ml of commercial bleach in the sealable container. Carefully add 3 ml of concentrated HCl to the bleach and immediately seal the container with its lid. 
		CAUTION: Bleach and HCl react to produce toxic chlorine gas which acts to surface-sterilize the seeds.</li>
		<li>Incubate the seeds in the presence of chlorine gas for 4 hr in the fumehood. 
		Note: Longer sterilization times will reduce germination efficiency.</li>
		<li>After sterilization, allow the chlorine gas to vent in the fume hood for at least 1 hr then seal the microcentrifuge tube. Leave the bleach and HCl mixture in the fumehood for at least 24 hr before discarding. 
		Note: Sterilized seeds may be stored at room temperature for immediate use.</li>
		<li>Keep seeds at 4 &#176;C for long-term storage. Bring seeds to room temperature before opening the microcentrifuge tube to prevent condensation. Store seeds in the dark.</li>
	</ol>
	</li>
	<li>Prepare Agar Plates in 4-sector Petri Dishes (90 x 15 mm):
	<ol>
		<li>Prepare 110 ml of growth medium for A. thaliana seedlings: 1x Murashige and Skoog (MS) basal medium15 (4.33 g/L) containing 1% (w/v) sucrose and 0.8% (w/v) agar. Adjust the MS medium to pH 6 with NaOH.</li>
		<li>Prepare 100 ml of bacterial growth medium for CEPA decomposition: Schramm and Hestrin (SH) medium16 containing 1.5% (w/v) agar. Adjust the SH medium to pH 7 with NaOH.</li>
		<li>Sterilize media by autoclaving and temper in a 55 &#176;C water bath.</li>
		<li>Once the MS agar has tempered, add 40 ml to a sterile flask. To prepare the positive control growth medium for A. thaliana seedlings, supplement the 40 ml aliquot of MS agar with 40 &#181;l of 10 mM ACC to obtain a final concentration of 10 &#181;M ACC.</li>
		<li>Add 5 ml of medium to the appropriate quadrants of the sectored Petri dishes (Figure 1) and allow the agar to solidify. Prepare all plates in triplicate. 
		Note: CEPA is not added to the growth medium until later in the protocol.</li>
	</ol>
	</li>
</ol>
<img alt="Figure 1" src="/files/ftp_upload/54682/54682fig1.jpg" /> 
Figure 1: Setup of agar plates used for the triple response assay with CEPA. A schematic illustrates the quadrants specific for the negative control (A), positive control (B), and experimental plates (C). This figure has been modified from Augimeri and Strap9. <a href="https://www-jove-com.bdigitaluss.remotexs.co/files/ftp_upload/54682/54682fig1large.jpg" target="_blank">Please click here to view a larger version of this figure.</a>
<ol start="3">
	<li>Stratify A. thaliana Seeds to Ensure Synchronous Germination:
	<ol>
		<li>Add approximately fifty A. thaliana seeds onto each quadrant containing MS or MS+ACC agar. Ensure seeds are evenly distributed to facilitate seedling removal and analysis.</li>
		<li>Incubate plates containing seeds in the dark at 4 &#176;C for 3-4 days.</li>
	</ol>
	</li>
	<li>Decompose CEPA on Bacterial Growth Medium (SH) and Perform Triple Response Assay:
	<ol>
		<li>After stratification, expose the seeds to fluorescent light for 2 hr.</li>
		<li>Spread 10 &#181;l of the 500 mM CEPA stock solution onto the quadrants of the experimental plates containing SH agar (pH 7; Figure 1) to obtain a final CEPA concentration of 1 mM.</li>
		<li>Seal the plates with laboratory film and cover with foil to create a dark environment for the seeds.</li>
		<li>Germinate seeds by incubating plates in the dark at 23 &#176;C for 3 days with the agar side down. 
		Note: Plates can be stacked, but negative controls should be placed on the bottom since ethylene is lighter than air.</li>
	</ol>
	</li>
	<li>Analyze Triple Response Assay Data:
	<ol>
		<li>With flame-sterilized forceps, remove single seedlings from a plate corresponding to each treatment and view under a dissecting or digital USB microscope. Ensure the bottom of the seedlings are aligned and photograph.</li>
		<li>Remove 30 seedlings from each quadrant (60 seedlings per biological replicate and 180 seedlings per treatment). Align on a surface with a black background and photograph with a ruler.</li>
		<li>Measure the hypocotyl length (mm) of replicate seedlings using ImageJ software17. Set the scale by clicking and dragging the *Straight* tool to select a length of 10 mm. Select &#34;Set Scale&#34; under the &#34;Analyze&#34; tab and set the known distance to 10. Using the *Segmented* tool, click and drag to select the length of the hypocotyl and press M to measure distance. Compare the means of biological replicates using a one-way ANOVA with a Tukey&#39;s multiple comparison test. Differences are considered significant if p &#60; 0.05.</li>
	</ol>
	</li>
</ol>
3. Analysis of pH throughout Bacterial Growth
<ol>
	<li>Grow and Quantify Komagataeibacter xylinus Starter Cultures in Triplicate:
	<ol>
		<li>Inoculate a single colony of K. xylinus into 5 ml of SH medium (pH 5) supplemented with 0.2% (v/v) filter-sterilized cellulase. Incubate cultures at 30 &#176;C with agitation at 150 rpm until an OD600 of 0.3 to 0.4 is reached (about 72 hr).</li>
		<li>Harvest starter cultures by centrifugation (2,000 x g; 4 &#176;C; 10 min). With 5 ml sterile 0.85% (w/v) NaCl solution, wash the cells twice and resuspend the cell pellet. Keep cells on ice.</li>
		<li>Quantify cells using a Petroff-Hausser counting chamber.</li>
	</ol>
	</li>
	<li>Inoculate Cultures for Analysis of pH:
	<ol>
		<li>Add 150 ml of SH broth (pH 7) supplemented with 0.2% (v/v) filter-sterilized cellulase to twelve 500 ml flasks with foil lids. Inoculate flasks with K. xylinus starter cultures at a concentration of 105 cells/ml. Using the three starter cultures, prepare three biological replicates per treatment.</li>
		<li>Supplement cultures with 300 &#181;l of the 5, 50, or 500 mM CEPA stock solutions to obtain final CEPA concentrations of 0.01, 0.1, and 1.0 mM, respectively. Supplement the untreated control cultures with 300 &#181;l of the solvent used to dissolve CEPA.</li>
		<li>Seal the flasks by tightly taping the foil lids to the flasks and incubate cultures for 14 days at 30 &#176;C with agitation at 150 rpm.</li>
	</ol>
	</li>
	<li>Each day, aseptically remove 5 ml samples from each flask and pellet cells by centrifugation (2,000 x g; 4 &#176;C; 10 min). Transfer supernatants to a clean tube and measure the pH of each biological replicate using a pH meter.</li>
	<li>Analyze the time-course data by graphing the mean pH of the biological replicates. 
	Note: It is important that the culture pH does not drop below 3.5; a culture pH of 5 significantly reduces ethylene release from CEPA, and a pH below 3.5 completely inhibits ethylene release.</li>
	<li>To control for chlorine and phosphate levels, perform an identical experiment using 0.01, 0.1, and 1.0 mM of the NaCl-NaH2PO4 solution using the 5, 50, and 500 mM stocks, respectively.</li>
</ol>
4. Colony Morphology
<ol>
	<li>Grow K. xylinus Starter Cultures in Triplicate:
	<ol>
		<li>Inoculate a single colony of K. xylinus into 5 ml of SH medium (pH 5) supplemented with 0.2% (v/v) filter-sterilized cellulase. Incubate cultures at 30 &#176;C with agitation at 150 rpm until an OD600 of 0.3 to 0.4 is reached (about 72 hr).</li>
		<li>Harvest starter cultures by centrifugation (2,000 x g; 4 &#176;C; 10 min). With 5 ml of sterile saline, wash the cells and then resuspend the cell pellet. Keep cells on ice.</li>
	</ol>
	</li>
	<li>Prepare 24 agar plates containing 25 ml of SH (pH 7) medium with 1.5% (w/v) agar.</li>
	<li>Once the agar has solidified, spread 50 &#181;l of the 5, 50, and 500 mM CEPA stock solutions on the agar to obtain final CEPA concentrations of 0.01, 0.1, and 1.0 mM, respectively. Set up untreated and solvent control plates, which consist of no amendment and spreading of 50 &#181;l of the solvent used to dissolve the test compounds.</li>
	<li>Streak plates for isolated colonies with a loop-full (~5 &#956;l) of K. xylinus starter culture and seal them with paraffin film. Inoculate all plates in triplicate. Incubate plates for five days at 30 &#176;C.</li>
	<li>Photograph colonies at 20X magnification using a digital USB microscope and qualitatively assess colonial morphology and cellulose production on solid medium. 
	Note: Cellulose appears as a hazy substance along the margin of the colony.</li>
	<li>To control for chlorine and phosphate levels, perform an identical experiment using 0.01, 0.1, and 1.0 mM of the NaCl-NaH2PO4 solution using the 5, 50, and 500 mM stocks, respectively.</li>
</ol>
5. Pellicle Assays
<ol>
	<li>Grow and Quantify K. xylinus Starter Cultures in Triplicate:
	<ol>
		<li>In triplicate, inoculate a single colony of K. xylinus into 5 ml of SH medium (pH 5) supplemented with 0.2% (v/v) filter-sterilized cellulase. Incubate cultures at 30 &#176;C with agitation at 150 rpm until an OD600 of 0.3 to 0.4 is reached (about 72 hr).</li>
		<li>Harvest starter cultures by centrifugation (2,000 x g; 4 &#176;C; 10 min). With 5 ml of sterile saline, wash the cells twice and resuspend the cell pellet. Keep cells on ice.</li>
		<li>Quantify cells using a Petroff-Hausser counting chamber.</li>
	</ol>
	</li>
	<li>Prepare Master Mixes to Inoculate 24-well Plates:
	<ol>
		<li>Supplement 60 ml of SH medium (pH 7) with 120 &#181;l of the 5, 50, and 500 mM CEPA stocks to obtain final CEPA concentrations of 0.01, 0.1, and 1.0 mM, respectively. Supplement another 60 ml of SH medium (pH 7) with 120 &#181;l of the solvent used to dissolve CEPA. Vortex to mix.</li>
		<li>Divide each 60 ml of CEPA-containing medium into four 14 ml aliquots. Inoculate three of the 14 ml aliquots with biological replicates of starter culture at a concentration of 105 cells/ml. Keep tubes with cells on ice to prevent cellulose production. 
		Note: The remaining 14 ml aliquot will be used for sterile control wells.</li>
	</ol>
	</li>
	<li>Inoculate 24-well Plates:
	<ol>
		<li>Test each treatment in its own plate with three rows of biological replicates and a row of sterile controls (Figure 2).</li>
	</ol>
	</li>
</ol>
<img alt="Figure 2" src="/files/ftp_upload/54682/54682fig2.jpg" /> 
Figure 2: Flow-chart illustrating the protocol used for pellicle assay and analysis. Stock CEPA-supplemented pH 7 SH medium (60 ml) is aliquoted for three separate biological replicate inoculations and a sterile control (14 ml each). These cultures are then aliquoted into six technical replicates (2 ml) into a 24 well plate and then sealed with paraffin film. After incubation for 7 days at 30 &#176;C, pellicles are harvested and characterized by determining wet weight, thickness, dry weight, and crystallinity by FT-IR. <a href="https://www-jove-com.bdigitaluss.remotexs.co/files/ftp_upload/54682/54682fig2large.jpg" target="_blank">Please click here to view a larger version of this figure</a>
<ol start="2" style="margin-left: 40px;">
	<li>Using the 14 ml master mix, add 2 ml into each of six wells of a sterile 24-well plate. Complete for the three biological replicates and sterile control (Figure 2). Repeat for each treatment.</li>
	<li>Seal plates with paraffin film and incubate statically for 7 days at 30 &#176;C.</li>
</ol>
<ol start="4">
	<li>Harvest and Measure Pellicle Wet Weight, Thickness, dry Weight (Cellulose Yield) and Crystallinity (Figure 2):
	<ol>
		<li>Depress one side of the pellicle to elevate the opposing pellicle edge and remove individual pellicles with forceps. While retaining grip, place them on fresh paper towel for 3 sec to remove excess medium before weighing to determine their wet weights.</li>
		<li>Align pellicles adjacent to a ruler and photograph from the side using a high resolution digital camera.</li>
		<li>Using ImageJ software17, measure pellicle thickness on the left shoulder, right shoulder and the center of each pellicle. Average all technical replicates for each biological replicate.</li>
		<li>Individually transfer the pellicles into the wells of a 6-well plate. Treat pellicles with 12 ml of 0.1 N NaOH at 80 &#176;C for 20 min to lyse cells.</li>
		<li>Remove the NaOH and neutralize pellicles by washing with ultra-pure water for 24 hr with agitation. Change water every 6 hr. 
		Note: Pellicles should be white upon completion of the washing step.</li>
		<li>Place pellicles on silicon mats and dry at 50 &#176;C for 48 hr to constant weight. Once dry, remove from mats and measure pellicle weights on an analytical scale to determine bacterial cellulose yield.</li>
		<li>Analyze pellicle crystallinity using Fourier-transform infrared spectroscopy (FT-IR) using 32 scans and a resolution of 4 cm-1 in the range of 4,000 to 650 cm-1. Calculate the crystallinity index, CI(IR), using A1437/A895; the absorbance ratio of the &#34;crystalline band&#34; and &#34;amorphous band&#34; as previously described18.</li>
	</ol>
	</li>
	<li>To control for chlorine and phosphate levels, perform an identical experiment using 0.01, 0.1, and 1.0 mM of the NaCl-NaH2PO4 solution using the 5, 50, and 500 mM stocks, respectively.</li>
	<li>Analyze Pellicle Data:
	<ol>
		<li>Calculate pellicle hydration by determining the difference between pellicle wet weight and dry weight.</li>
		<li>Average the values of all technical replicates to obtain a single value for each biological replicate for statistical analysis. Compare treatments using a one-way ANOVA with Tukey&#39;s multiple comparison test. Differences are significant if p &#60;0.05.</li>
		<li>Normalize data as the percent of untreated controls and plot the means of biological replicates.</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Guzm&#225;n, P., Ecker, J. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Exploiting+the+triple+response+of+Arabidopsis+to+identify+ethylene-related+mutants.">Exploiting the triple response of Arabidopsis to identify ethylene-related mutants.</a> Plant Cell. 2 (6), 513-523 (1990).</li><li>Bakshi, A., Shemansky, J. M., Chang, C., Binder, B. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=History+of+research+on+the+plant+hormone+ethylene.">History of research on the plant hormone ethylene.</a> J. Plant Growth Regul. 34 (4), 809-827 (2015).</li><li>Schaller, G. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ethylene+and+the+regulation+of+plant+development.">Ethylene and the regulation of plant development.</a> BMC Biol. 10 (1), (2012).</li><li>Hua, J., Sakai, H., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=EIN4+and+ERS2+are+members+of+the+putative+ethylene+receptor+gene+family+in+Arabidopsis.">EIN4 and ERS2 are members of the putative ethylene receptor gene family in Arabidopsis.</a> Plant Cell. 10 (8), 1321-1332 (1998).</li><li>Bleecker, A. B., Estelle, M. A., Somerville, C., Kende, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Insensitivity+to+ethylene+conferred+by+a+dominant+Mutation+in+Arabidopsis+thaliana.">Insensitivity to ethylene conferred by a dominant Mutation in Arabidopsis thaliana.</a> Science. 241 (4869), 1086-1089 (1988).</li><li>Hamilton, A. J., Bouzayen, M., Grierson, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Identification+of+a+tomato+gene+for+the+ethylene-forming+enzyme+by+expression+in+yeast.">Identification of a tomato gene for the ethylene-forming enzyme by expression in yeast.</a> Proc. Natl. Acad. Sci. 88 (16), 7434-7437 (1991).</li><li>Kim, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Assessment+of+ethylene+removal+with+Pseudomonas+strains.">Assessment of ethylene removal with Pseudomonas strains.</a> J. Hazard. Mater. 131 (3), 131-136 (2006).</li><li>Kim, H. E., Shitashiro, M., Kuroda, A., Takiguchi, N., Kato, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ethylene+chemotaxis+in+Pseudomonas+aeruginosa+and+other+Pseudomonas+species.">Ethylene chemotaxis in Pseudomonas aeruginosa and other Pseudomonas species.</a> Microbes Environ. 22 (2), 186-189 (2007).</li><li>Augimeri, R. V., Strap, J. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=The+phytohormone+ethylene+enhances+bacterial+cellulose+production,+regulates+CRP/FNRKx+transcription+and+causes+differential+gene+expression+within+the+cellulose+synthesis+operon+of+Komagataeibacter+(Gluconacetobacter)+xylinus+ATCC+53582.">The phytohormone ethylene enhances bacterial cellulose production, regulates CRP/FNRKx transcription and causes differential gene expression within the cellulose synthesis operon of Komagataeibacter (Gluconacetobacter) xylinus ATCC 53582.</a> Front. Microbiol. 6, 1459 (2015).</li><li>Zhang, W., Wen, C. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Preparation+of+ethylene+gas+and+comparison+of+ethylene+responses+induced+by+ethylene,+ACC,+and+ethephon.">Preparation of ethylene gas and comparison of ethylene responses induced by ethylene, ACC, and ethephon.</a> Plant Physiol. Biochem. 48 (1), 45-53 (2010).</li><li>Zhang, W., Hu, W., Wen, C. K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ethylene+preparation+and+its+application+to+physiological+experiments.">Ethylene preparation and its application to physiological experiments.</a> Plant Signal. Behav. 5 (4), 453-457 (2010).</li><li>Warner, H. L., Leopold, A. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ethylene+evolution+from+2-chloroethylphosphonic+acid.">Ethylene evolution from 2-chloroethylphosphonic acid.</a> Plant Physiol. 44 (1), 156-158 (1969).</li><li>Biddle, E., Kerfoot, D. G. S., Kho, Y. H., Russell, K. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Kinetic+studies+of+the+thermal+decomposition+of+2-chloroethylphosphonic+acid+in+aqueous+solution.">Kinetic studies of the thermal decomposition of 2-chloroethylphosphonic acid in aqueous solution.</a> Plant Physiol. 58 (5), 700-702 (1976).</li><li>Klein, I., Lavee, S., Ben-Tal, Y. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effect+of+water+vapor+pressure+on+the+thermal+decomposition+of+2-chloroethylphosphonic+acid.">Effect of water vapor pressure on the thermal decomposition of 2-chloroethylphosphonic acid.</a> Plant Physiol. 63 (3), 474-477 (1979).</li><li>Murashige, T., Skoog, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+revised+medium+for+rapid+growth+and+bio+assays+with+tobacco+tissue+cultures.">A revised medium for rapid growth and bio assays with tobacco tissue cultures.</a> Physiol. Plant. 15 (3), 473-497 (1962).</li><li>Schramm, M., Hestrin, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Factors+affecting+production+of+cellulose+at+the+air/liquid+interface+of+a+culture+of+Acetobacter+xylinum.">Factors affecting production of cellulose at the air/liquid interface of a culture of Acetobacter xylinum.</a> J. Gen. Microbiol. 11 (1), 123-129 (1954).</li><li>Schneider, C. A., Rasband, W. S., Eliceiri, K. W. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=NIH+Image+to+ImageJ:+25+years+of+image+analysis.">NIH Image to ImageJ: 25 years of image analysis.</a> Nat. Methods. 9 (7), 671-675 (2012).</li><li>Ciolacu, D., Ciolacu, F., Popa, V. I. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Amorphous+cellulose-structure+and+characterization.">Amorphous cellulose-structure and characterization.</a> Cellul. Chem. Technol. 45 (1), 13-21 (2011).</li></ol>

The authors have nothing to disclose.

The methods described here outline the in situ production of ethylene from CEPA for the study of bacterial ethylene response using the model organism, K. xylinus. This method is very useful as ethylene can be produced by supplementing any aqueous medium that has a pH greater than 3.510,11 with CEPA negating the need for pure ethylene gas or specialized laboratory equipment. This method is not limited to studying the effects of CEPA-derived ethylene on bacteria but can be also be adapted to st...

The olefin ethylene (C2H4) was first discovered as a plant hormone in 1901 when it was observed that pea seedlings, grown in a laboratory that used coal gas lamps, exhibited an abnormal morphology in which stems (hypocotyls) were shorter, thicker and bent sideways compared to normal pea seedlings; a phenotype later termed the triple response1,2. Subsequent studies demonstrated that ethylene is a vital phytohormone that regulates numerous developmental processes such as growth, stress response, fruit ripening and senescence3. Arabidopsis thaliana, a model organism for plant biology research, has been well studied in regards to its response to ethylene. Several ethylene response mutants have been isolated by exploiting the triple response phenotype observed in dark-grown A. thaliana seedlings in the presence of ethylene1,4,5. The biosynthetic precursor for ethylene production in plants is 1-aminocyclopropane carboxylic acid (ACC)6 and is commonly used during the triple response assay to increase endogenous ethylene production that leads to the triple response phenotype1,4,5.
Although the ethylene response is widely studied in plants, the effect of exogenous ethylene on bacteria is vastly understudied despite the close association of bacteria with plants. One study reported that certain Pseudomonas strains can survive using ethylene as a sole source of carbon and energy7. However, only two studies have demonstrated that bacteria respond to ethylene. The first study showed that strains of Pseudomonas aeruginosa, P. fluorescens, P. putida, and P. syringae were chemotactic toward ethylene using an agarose plug assay in which molten agarose was mixed with a chemotaxis buffer equilibrated with pure ethylene gas8. However, to our knowledge, there have been no further reports using pure ethylene gas to characterize bacterial ethylene response, likely due to the difficultly of handling gases in the laboratory without specialized equipment. The second report of bacterial ethylene response demonstrated that ethylene increased bacterial cellulose production and influenced gene expression in the fruit-associated bacterium, Komagataeibacter (formerly Gluconacetobacter) xylinus9. In this case, the ethylene-releasing compound, 2-chloroethylphosphonic acid (CEPA) was used to produce ethylene in situ within the bacterial growth medium, bypassing the need for pure ethylene gas or specialized equipment.
CEPA produces ethylene at a 1:1 molar ratio above pH 3.510,11 through a base-catalyzed, first-order reaction12-14. The degradation of CEPA is positively correlated with pH and temperature13,14 and results in the production of ethylene, chloride and phosphate. CEPA provides researchers interested in studying bacterial responses to ethylene with a convenient alternative to gaseous ethylene.
The overall goal of the following protocols is to provide a simple and efficient method to study bacterial ethylene response and includes validation of physiologically relevant levels of ethylene production from CEPA decomposition in bacterial growth medium, analysis of culture pH to ensure CEPA decomposition is not impaired during bacterial growth, and assessment of the effect of ethylene on bacterial morphology and phenotype. We demonstrate these protocols using K. xylinus, however, these protocols can be adapted to study ethylene response in other bacteria by using the appropriate growth medium and phenotype analyses.

<table><tbody><tr><td>1-aminocyclopropane carboxylic acid (ACC)</td><td>Sigma</td><td>A3903</td><td>Biosynthetic precursor of ethylene in plants</td></tr><tr><td>4-sector Petri dish</td><td>Phoenix Biomedical</td><td>CA73370-022</td><td>For testing triple response</td></tr><tr><td>Agar</td><td>BioShop</td><td>AGR001.1</td><td>To solidify medium</td></tr><tr><td>Canon Rebel T1i DLSR camera</td><td>Canon</td><td>3818B004</td><td>For pictures of pellicles</td></tr><tr><td>Cellulase from Trichoderma reesei ATCC 26921&amp;nbsp;</td><td>Sigma</td><td>C2730</td><td>Aqueous solution</td></tr><tr><td>Citric acid</td><td>BioShop</td><td>CIT002.500</td><td>For SH medium</td></tr><tr><td>Commercial bleach</td><td>Life Brand</td><td>57800861874</td><td>Bleach for seed sterilization</td></tr><tr><td>Concentrated HCl</td><td>BioShop</td><td>HCL666.500</td><td>Hydrochloric acid for pH adjustment</td></tr><tr><td>Digital USB microscope</td><td>Plugable</td><td>N/A</td><td>For pictures of colonies</td></tr><tr><td>Ethephon (&amp;ge;96%; 2-chloroethylphosphonic acid)</td><td>Sigma</td><td>C0143</td><td>Ethylene-releasing compound</td></tr><tr><td>Glucose</td><td>BioBasic</td><td>GB0219</td><td>For SH medium</td></tr><tr><td>Komagataeibacter xylinus ATCC 53582</td><td>ATCC</td><td>53582</td><td>Bacterial cellulose-producing alphaproteobacterium</td></tr><tr><td>Microcentrifuge tube</td><td>LifeGene</td><td>LMCT1.7B</td><td>1.7 ml microcentrifuge tube</td></tr><tr><td>Murashige and Skoog (MS) basal medium&amp;nbsp;</td><td>Sigma</td><td>M5519</td><td>Arabidopsis thaliana growth medium</td></tr><tr><td>Na&lt;sub&gt;2&lt;/sub&gt;HPO&lt;sub&gt;4&lt;/sub&gt;&amp;middot;7H&lt;sub&gt;2&lt;/sub&gt;O&amp;nbsp;</td><td>BioShop</td><td>SPD579.500</td><td>Sodium phosphate, dibasic heptahydrate for SH medium</td></tr><tr><td>NaCl</td><td>BioBasic</td><td>SOD001.1</td><td>Sodium chloride for saline and control solution</td></tr><tr><td>NaH&lt;sub&gt;2&lt;/sub&gt;PO&lt;sub&gt;4&lt;/sub&gt;&amp;middot;H&lt;sub&gt;2&lt;/sub&gt;O&amp;nbsp;</td><td>BioShop</td><td>SPM306.500</td><td>Sodium phosphate, monobasic monohydrate for control solution</td></tr><tr><td>NaOH</td><td>BioShop</td><td>SHY700.500</td><td>Sodium hydroxide for pH adjustment</td></tr><tr><td>Paraffin film</td><td>Parafilm</td><td>PM996</td><td>For sealing plates and flasks</td></tr><tr><td>Peptone (bacteriological)</td><td>BioShop</td><td>PEP403.1</td><td>For SH medium</td></tr><tr><td>Petroff-Hausser counting chamber</td><td>Hausser scientific</td><td>3900</td><td>Bacterial cell counting chamber</td></tr><tr><td>Polyethersulfone sterilization filter 0.2 &amp;micro;m</td><td>VWR</td><td>28145-501</td><td>For sterilizing cellulase</td></tr><tr><td>Sucrose</td><td>BioShop</td><td>SUC600.1</td><td>Sucrose for MS medium</td></tr><tr><td>Yeast extract</td><td>BioBasic</td><td>G0961</td><td>For SH medium</td></tr></tbody></table>

utilizing the ethylene-releasing compound, 2-chloroethylphosphonic acid, as a tool to study ethylene response in bacteria

Ethylene (C2H4) is a gaseous phytohormone that is involved in numerous aspects of plant development, playing a dominant role in senescence and fruit ripening. Exogenous ethylene applied during early plant development triggers the triple response phenotype; a shorter and thicker hypocotyl with an exaggerated apical hook. Despite the intimate relationship between plants and bacteria, the effect of exogenous ethylene on bacteria has been greatly overlooked. This is partly due to the difficulty of controlling gaseous ethylene within the laboratory without specialized equipment. 2-Chloroethylphosphonic acid (CEPA) is a compound that decomposes into ethylene, chlorine, and phosphate in a 1:1:1:1 molar ratio when dissolved in an aqueous medium of pH 3.5 or greater. Here we describe the use of CEPA to produce in situ ethylene for the investigation of ethylene response in bacteria using the fruit-associated, cellulose-producing bacterium Komagataeibacter xylinus as a model organism. The protocols described herein include both the verification of ethylene production from CEPA via the Arabidopsis thaliana triple response assay and the effects of exogenous ethylene on K. xylinus cellulose production, pellicle properties and colonial morphology. These protocols can be adapted to examine the effect of ethylene on other microbes using appropriate growth media and phenotype analyses. The use of CEPA provides researchers with a simple and efficient alternative to pure ethylene gas for the routine determination of bacterial ethylene response.

A schematic plate setup for verification of ethylene liberation from CEPA in SH medium (pH 7) by the triple response assay is shown in Figure 1A-C. A flow-chart illustrating the pellicle protocol is shown in Figure 2. Dark-grown A. thaliana seedlings exhibit the triple response phenotype (shorter and thicker hypocotyl with an exaggerated apical hook) in the presence of ACC and in the presence of ethylene produced through the dec...

Watch this Scientific Journal Video about Utilizing the Ethylene-releasing Compound, 2-Chloroethylphosphonic Acid, as a Tool to Study Ethylene Response in Bacteria at JoVE.com

Utilizing the Ethylene-releasing Compound, 2-Chloroethylphosphonic Acid, as a Tool to Study Ethylene Response in Bacteria

The protocols outlined herein facilitate the convenient investigation of bacterial ethylene responses by utilizing 2-chloroethylphosphonic acid (CEPA). Ethylene is produced in situ through the decomposition of CEPA in an aqueous bacterial growth medium, circumventing the requirement for pure ethylene gas.

Ethylene (C2H4) is a gaseous phytohormone that is involved in numerous aspects of plant development, playing a dominant role in senescence and fruit ...

utilizing-ethylene-releasing-compound-2-chloroethylphosphonic-acid-as

Universidad San Sebastian

Research

JoVE Journal

Biochemistry

7.9K Views.  University of Ontario Institute of Technology. The protocols outlined herein facilitate the convenient investigation of bacterial ethylene responses by utilizing 2-chloroethylphosphonic acid (CEPA). Ethylene is produced in situ through the decomposition of CEPA in an aqueous bacterial growth medium, circumventing the requirement for pure ethylene gas. 

Video: Utilizing the Ethylene-releasing Compound, 2-Chloroethylphosphonic Acid, as a Tool to Study Ethylene Response in Bacteria

Protocols for Robust Herbicide Resistance Testing in Different Weed Species

Robust protocols to test putative herbicide resistant weed populations at whole plant level are essential to confirm the resistance status. The presented protocols, based on whole-plant bioassays performed in a greenhouse, can be readily adapted to a wide range of weed species and herbicides through appropriate variants. Seed samples from plants that survived a field herbicide treatment are collected and stored dry at low temperature until used. Germination methods differ according to weed species and seed dormancy type. Seedlings at similar growth stage are transplanted and maintained in the greenhouse under appropriate conditions until plants have reached the right growth stage for herbicide treatment. Accuracy is required to prepare the herbicide solution to avoid unverifiable mistakes. Other critical steps such as the application volume and spray speed are also evaluated. The advantages of this protocol, compared to others based on whole plant bioassays using one herbicide dose, are related to the higher reliability and the possibility of inferring the resistance level. Quicker and less expensive in vivo or in vitro diagnostic screening tests have been proposed (Petri dish bioassays, spectrophotometric tests), but they provide only qualitative information and their widespread use is hindered by the laborious set-up that some species may require. For routine resistance testing, the proposed whole plant bioassay can be applied at only one herbicide dose, so reducing the costs.

A robust and flexible approach to confirm herbicide resistance in weed populations is presented. This protocol allows the herbicide resistance levels to be inferred and applied to a wide range of weed species and herbicides with minor adaptations.

Robust protocols to test putative herbicide resistant weed populations at whole plant level are essential to confirm the resistance status. The presented ...

Environment

Adherence of Bacteria to Plant Surfaces Measured in the Laboratory

This manuscript describes a method to measure bacterial binding to axenic plant surfaces in the light microscope and through the use of viable cell counts. Plant materials used include roots, sprouts, leaves, and cut fruits. The methods described are inexpensive, easy, and suitable for small sample sizes. Binding is measured in the laboratory and a variety of incubation media and conditions can be used. The effect of inhibitors can be determined. Situations that promote and inhibit binding can also be assessed. In some cases it is possible to distinguish whether various conditions alter binding primarily due to their effects on the plant or on the bacteria.

An easy method for measuring and characterizing bacterial adhesion to plants, particularly roots and sprouts, is described in this article.

This manuscript describes a method to measure bacterial binding to axenic plant surfaces in the light microscope and through the use of viable cell ...

Quantification of the Potential Impact of Glyphosate-Based Products on Microbiomes

Glyphosate-based products (GBP) are the most common broad-spectrum herbicides worldwide. The target of glyphosate is the enzyme 5-enolpyruvylshikimate-3-phosphate synthase (EPSPS) in the shikimate pathway, which is virtually universal in plants. The inhibition of the enzyme stops the production of three essential amino acids: phenylalanine, tyrosine, and tryptophan. EPSPS is also present in fungi and prokaryotes, such as archaea and bacteria; thus, the use of GBP may have an impact on the microbiome composition of soils, plants, herbivores, and secondary consumers. This article aims to present general guidelines to assess the effect of GBP on microbiomes from field experiments to bioinformatics analyses and provide a few testable hypotheses. Two field experiments are presented to test the GBP on non-target organisms. First, plant-associated microbes from 10 replicated control and GBP treatment plots simulating no-till cropping are sampled and analyzed. In the second experiment, samples from experimental plots fertilized by either poultry manure containing glyphosate residues or non-treated control manure were obtained. Bioinformatics analysis of EPSPS protein sequences is utilized to determine the potential sensitivity of microbes to glyphosate. The first step in estimating the effect of GBP on microbiomes is to determine their potential sensitivity to the target enzyme (EPSPS). Microbial sequences can be obtained either from public repositories or by means of PCR amplification. However, in the majority of field studies, microbiome composition has been determined based on universal DNA markers such as the 16S rRNA and the internal transcribed spacer (ITS). In these cases, sensitivity to glyphosate can only be estimated through a probabilistic analysis of EPSPS sequences using closely related species. The quantification of the potential sensitivity of organisms to glyphosate, based on the EPSPS enzyme, provides a robust approach for further experiments to study target and non-target resistant mechanisms.

Glyphosate-based products (GBP) are the most common broad-spectrum herbicides worldwide. In this article, we introduce general guidelines to quantify the effect of GBP on microbiomes, from field experiments to bioinformatics analyses.

Glyphosate-based products (GBP) are the most common broad-spectrum herbicides worldwide. The target of glyphosate is the enzyme ...

Bacterial Leaf Infiltration Assay for Fine Characterization of Plant Defense Responses using the Arabidopsis thaliana-Pseudomonas syringae Pathosystem

In the absence of specialized mobile immune cells, plants utilize their localized programmed cell death and Systemic Acquired Resistance to defend themselves against pathogen attack. The contribution of a specific Arabidopsis gene to the overall plant immune response can be specifically and quantitatively assessed by assaying the pathogen growth within the infected tissue. For over three decades, the hemibiotrophic bacterium Pseudomonas syringae pv. maculicola ES4326 (Psm ES4326) has been widely applied as the model pathogen to investigate the molecular mechanisms underlying the Arabidopsis immune response. To deliver pathogens into the leaf tissue, multiple inoculation methods have been established, e.g., syringe infiltration, dip inoculation, spray, vacuum infiltration, and flood inoculation. The following protocol describes an optimized syringe infiltration method to deliver virulent Psm ES4326 into leaves of adult soil-grown Arabidopsis plants and accurately screen for enhanced disease susceptibility (EDS) towards this pathogen. In addition, this protocol can be supplemented with multiple pre-treatments to further dissect specific immune defects within different layers of plant defense, including Salicylic Acid (SA)-Triggered Immunity (STI) and MAMP-Triggered Immunity (MTI).

Bacterial Leaf Infiltration Assay for Fine Characterization of Plant Defense Responses using the Arabidopsis thaliana-Pseudomonas syringae Pathosystem

Quantification of pathogen growth is a powerful tool to characterize various Arabidopsis thaliana (hereafter: Arabidopsis) immune responses. The method described here presents an optimized syringe infiltration assay to quantify the Pseudomonas syringae pv. maculicola ES4326 growth in adult Arabidopsis leaves.

In the absence of specialized mobile immune cells, plants utilize their localized programmed cell death and Systemic Acquired Resistance to defend ...

Immunology and Infection

Antimicrobial Peptides Produced by Selective Pressure Incorporation of Non-canonical Amino Acids

Nature has a variety of possibilities to create new protein functions by modifying the sequence of the individual amino acid building blocks. However, all variations are based on the 20 canonical amino acids (cAAs). As a way to introduce additional physicochemical properties into polypeptides, the incorporation of non-canonical amino acids (ncAAs) is increasingly used in protein engineering. Due to their relatively short length, the modification of ribosomally synthesized and post-translationally modified peptides by ncAAs is particularly attractive. New functionalities and chemical handles can be generated by specific modifications of individual residues. The selective pressure incorporation (SPI) method utilizes auxotrophic host strains that are deprived of an essential amino acid in chemically defined growth media. Several structurally and chemically similar amino acid analogs can then be activated by the corresponding aminoacyl-tRNA synthetase and provide residue-specific cAA(s) &#8594; ncAA(s) substitutions in the target peptide or protein sequence. Although, in the context of the SPI method, ncAAs are also incorporated into the host proteome during the phase of recombinant gene expression, the majority of the cell&#39;s resources are assigned to the expression of the target gene. This enables efficient residue-specific incorporation of ncAAs often accompanied with high amounts of modified target. The presented work describes the in vivo incorporation of six proline analogs into the antimicrobial peptide nisin, a lantibiotic naturally produced by Lactococcus lactis. Antimicrobial properties of nisin can be changed and further expanded during its fermentation and expression in auxotrophic Escherichia coli strains in defined growth media. Thereby, the effects of residue-specific replacement of cAAs with ncAAs can deliver changes in antimicrobial activity and specificity. Antimicrobial activity assays and fluorescence microscopy are used to test the new nisin variants for growth inhibition of a Gram-positive Lactococcus lactis indicator strain. Mass spectroscopy is used to confirm ncAA incorporation in bioactive nisin variants.

The protocol presents the Escherichia coli-based selective pressure incorporation of non-canonical amino acids (ncAAs) into the lactococcal antimicrobial peptide nisin. Its properties can be changed during recombinant expression via substitution with desired ncAAs in defined growth media. Resulting changes in bioactivity are mapped by growth inhibition assays and fluorescence microscopy.

Nature has a variety of possibilities to create new protein functions by modifying the sequence of the individual amino acid building blocks. However, all ...

Bioengineering

Chronoamperometry Analysis of EET in Lactiplantibacillus plantarum with DHNA

Characterizing Mediated Extracellular Electron Transfer in Lactic Acid Bacteria with a Three-Electrode, Two-Chamber Bioelectrochemical System

Many bacteria perform extracellular electron transfer (EET), whereby electrons are transferred from the cell to an extracellular terminal electron acceptor. This electron acceptor can be an electrode and electrons can be delivered indirectly via a redox-active mediator molecule. Here, we present a protocol to study mediated EET in Lactiplantibacillus plantarum, a probiotic lactic acid bacterium widely used in the food industry, using a bioelectrochemical system. We detail how to assemble a three-electrode, two-chambered bioelectrochemical system and provide guidance on characterizing EET in the presence of a soluble mediator using chronoamperometry and cyclic voltammetry techniques. We use representative data from 1,4-dihydroxy-2-naphthoic acid (DHNA)-mediated EET experiments with L. plantarum to demonstrate data analysis and interpretation. The techniques described in this protocol can open new opportunities for electro-fermentation and bioelectrocatalysis. Recent applications of this electrochemical technique with L. plantarum demonstrated an acceleration of metabolic flux towards producing fermentation end-products, which are critical flavor components in food fermentation. As such, this system has the potential to be further developed to alter flavors in food production or produce valuable chemicals.

Here we present a protocol for characterizing mediated extracellular electron transfer (EET) in lactic acid bacteria using a three-electrode, two-chamber bioelectrochemical system. We illustrate this method with Lactiplantibacillus plantarum and the redox mediator 1,4-dihydroxy-2-naphthoic acid and provide a thorough description of the electrochemical techniques used to evaluate mediated EET.

Many bacteria perform extracellular electron transfer (EET), whereby electrons are transferred from the cell to an extracellular terminal electron ...

Detection of Histone Modifications in Plant Leaves

Chromatin structure is important for the regulation of gene expression in eukaryotes. In this process, chromatin remodeling, DNA methylation, and covalent modifications on the amino-terminal tails of histones H3 and H4 play essential roles1-2. H3 and H4 histone modifications include methylation of lysine and arginine, acetylation of lysine, and phosphorylation of serine residues1-2. These modifications are associated either with gene activation, repression, or a primed state of gene that supports more rapid and robust activation of expression after perception of appropriate signals (microbe-associated molecular patterns, light, hormones, etc.)3-7. 
Here, we present a method for the reliable and sensitive detection of specific chromatin modifications on selected plant genes. The technique is based on the crosslinking of (modified) histones and DNA with formaldehyde8,9, extraction and sonication of chromatin, chromatin immunoprecipitation (ChIP) with modification-specific antibodies9,10, de-crosslinking of histone-DNA complexes, and gene-specific real-time quantitative PCR. The approach has proven useful for detecting specific histone modifications associated with C4 photosynthesis in maize5,11 and systemic immunity in Arabidopsis3.

A reliable and useful approach to detect histone modifications on specific plant genes is described. The approach combines chromatin immunoprecipitation (ChIP) and real-time quantitative PCR. It allows detection of histone modifications on specific genes with a role in diverse physiological processes.

Chromatin structure is important for the regulation of gene expression in eukaryotes. In this process, chromatin remodeling, DNA methylation, and covalent ...

Biology

Pattern-Triggered Oxidative Burst and Seedling Growth Inhibition Assays in Arabidopsis thaliana

Plants have evolved a robust immune system to perceive pathogens and protect against disease. This paper describes two assays that can be used to measure the strength of immune activation in Arabidopsis thaliana following treatment with elicitor molecules. Presented first is a method for capturing the rapidly-induced and dynamic oxidative burst, which can be monitored using a luminol-based assay. Presented second is a method describing how to measure immune-induced inhibition of seedling growth. These protocols are fast and reliable, do not require specialized training or equipment, and are widely used to understand the genetic basis of plant immunity.

Pattern-Triggered Oxidative Burst and Seedling Growth Inhibition Assays in Arabidopsis thaliana

This paper describes two methods for quantifying defense responses in Arabidopsis thaliana following exposure to immune elicitors: the transient oxidative burst, and the inhibition of seedling growth.

Plants have evolved a robust immune system to perceive pathogens and protect against disease. This paper describes two assays that can be used to measure ...

Visualization of Bacterial Resistance using Fluorescent Antibiotic Probes

Fluorescent antibiotics are multipurpose research tools that are readily used for the study of antimicrobial resistance, due to their significant advantage over other methods. To prepare these probes, azide derivatives of antibiotics are synthesized, then coupled with alkyne-fluorophores using azide-alkyne dipolar cycloaddition by click chemistry. Following purification, the antibiotic activity of the fluorescent antibiotic is tested by minimum inhibitory concentration assessment. In order to study bacterial accumulation, either spectrophotometry or flow cytometry may be used, allowing for much simpler analysis than methods relying on radioactive antibiotic derivatives. Furthermore, confocal microscopy can be used to examine localization within the bacteria, affording valuable information about mode of action and changes that occur in resistant species. The use of fluorescent antibiotic probes in the study of antimicrobial resistance is a powerful method with much potential for future expansion.

Fluorescently tagged antibiotics are powerful tools that can be used to study multiple aspects of antimicrobial resistance. This article describes the preparation of fluorescently tagged antibiotics and their application to studying antibiotic resistance in bacteria. Probes can be used to study mechanisms of bacterial resistance (e.g., efflux) by spectrophotometry, flow cytometry, and microscopy.

Fluorescent antibiotics are multipurpose research tools that are readily used for the study of antimicrobial resistance, due to their significant ...

Bacteriophage Effectiveness for Biocontrol of Foodborne Pathogens Evaluated via High-Throughput Settings

Bacterial pathogens continually challenge food safety systems worldwide. With increasing concerns about the emergence of heat- and sanitizer-resistant bacteria, novel antibacterial agents, are urgently needed. A bacteriophage-based biocontrol strategy is the therapeutic use of phages to control bacterial pathogens in agricultural settings. Phage biocontrol is increasingly accepted as a sustainable technology, effective at decontaminating foodborne pathogens. To ensure effective biocontrol outcomes, systematic screening of phage combinations against targeted bacteria under required environmental conditions is crucial. Antibacterial efficacy of phage cocktails may be affected by phage genera and combination, targeted bacterial strains, the multiplicity of infection, temperature, and time. To formulate a phage cocktail with superior efficacy, the proposed method was to systematically evaluate the effectiveness of individual phages and phage cocktails in killing foodborne bacterial pathogens under targeted conditions. Bacterial killing efficacy was monitored by measuring optical density at desired temperatures and durations. Superior phage efficacy was determined by complete inhibition of bacterial growth. The proposed method is a robust, evidence-based approach to facilitate formulating phage cocktails with superior antibacterial efficacy.

This protocol describes a robust method for using high-throughput settings to screen the antibacterial efficacy of bacteriophage cocktails.

Bacterial pathogens continually challenge food safety systems worldwide. With increasing concerns about the emergence of heat- and sanitizer-resistant ...

Utilizing the Ethylene-releasing Compound, 2-Chloroethylphosphonic Acid, as a Tool to Study Ethylene Response in Bacteria

Podsumowanie

Przeglądaj więcej filmów

Rozdziały w tym wideo

Protocols for Robust Herbicide Resistance Testing in Different Weed Species

Adherence of Bacteria to Plant Surfaces Measured in the Laboratory

Quantification of the Potential Impact of Glyphosate-Based Products on Microbiomes

Bacterial Leaf Infiltration Assay for Fine Characterization of Plant Defense Responses using the Arabidopsis thaliana-Pseudomonas syringae Pathosystem

Antimicrobial Peptides Produced by Selective Pressure Incorporation of Non-canonical Amino Acids

Characterizing Mediated Extracellular Electron Transfer in Lactic Acid Bacteria with a Three-Electrode, Two-Chamber Bioelectrochemical System

Detection of Histone Modifications in Plant Leaves

Pattern-Triggered Oxidative Burst and Seedling Growth Inhibition Assays in Arabidopsis thaliana

Visualization of Bacterial Resistance using Fluorescent Antibiotic Probes

Bacteriophage Effectiveness for Biocontrol of Foodborne Pathogens Evaluated via High-Throughput Settings