Name: design and use of a low cost, automated morbidostat for adaptive evolution of bacteria under antibiotic drug selection
Uploaded: 2016-09-27T15:00:00.000+00:00
Duration: 10 min 50 s
Description: Watch this Scientific Journal Video about Design and Use of a Low Cost, Automated Morbidostat for Adaptive Evolution of Bacteria Under Antibiotic Drug Selection at JoVE.com

The authors would like to thank Prof. Sze-Bi Hsu and Ms. Zhenzhen for useful discussions and help in the theoretical analysis and numerical simulation. Y. T. Y. would like to acknowledge funding support from the Ministry of Science and Technology under grant numbers MOST 103-2220-E-007-026 and MOST 104-2220-E-007-011, and from the National Tsing Hua University under grant numbers 103N2042E1, 104N2042E1, and 105N518CE1.

1. Assembly and Pretesting of the Morbidostat Device
<ol>
	<li>Assembly of the Morbidostat
	<ol>
		<li>Punch 3 holes on the cap of the culture vial with an 18 G syringe needle. Cut three pieces of polyethylene tubing ~7 cm in length. Insert these three pieces of polyethylene tubing on the cap.</li>
		<li>Use tape to wrap the edge of the cap to serve as the cast for the polydimethylsiloxane (PDMS) mixture. Mix 5 g of A component and 0.5 g of B component of the PDMS in a 150 ml plastic container by stirring manually with a toothpick. Load the mixture into a 10 ml syringe.
		<ol>
			<li>Pour the PDMS mixture on the cap with the syringe. Bake the entire cap to cure the PDMS for 8 hr in the oven at 70 &#176;C.</li>
		</ol>
		</li>
		<li>Solder the LED anode with the 24 gauge wire and LED cathode with the carbon resistor with a soldering iron. Solder a 680&#160;&#937; carbon resistor with a 24 G wire. Insulate the wire connection using electrical tape.</li>
		<li>Solder the collector of the photodetector with the 24 G wire and the emitter of the photodetector with a 100 k&#937; carbon resistor. Insulate the wire connection using electrical tape.</li>
		<li>Place the light emitting diode in the culture vial holder. By following the circuit diagram in Supplementary Figure 2, connect the light emitting diode and power it with a power supply of 5 V. Ensure that the LED works by using a digital camera that can detect IR (e.g., a mobile phone camera).</li>
		<li>Place the photodetector in the culture vial holder. By following the circuit diagram in Supplementary Figure 2, connect the photodetector and power it with a power supply of 5 V. Connect the wire to both sides of the photodetector resistors to measure the voltage across the electronic control board.</li>
		<li>Glue a magnet on the shaft of the cooling fan, which serves as the magnetic stirrer unit. Note that the alignment of the shaft of the fan to the culture vial, and the spacing between the culture vial and the magnet is very critical for the proper function of the magnetic stirring unit.</li>
		<li>Connect each piece of polyethylene tubing of the culture vial into the corresponding piece of silicone tubing for the micro-pumps, medium bottles, and waste bottle. Turn on the pump for 1 hr and measure the total volume being pumped from the medium bottle to the culture vial to determine the pump rate. Note that the typical pumping rate should be ~4 ml/hr, which corresponds to the dilution rate D = 0.33 hr&#8722;1 for a 12 ml working volume of the culture vial.</li>
		<li>Place the whole assembly on a mid-sized (34 cm x 34 cm x 43.5 cm) shaker incubator.</li>
	</ol>
	</li>
	<li>Pretesting the Morbidostat
	<ol>
		<li>Set power supply voltage of cool fan to 5 V to start its motor to test the magnetic stirring bar. Note that the stirring action can be inspected visually. The voltage that drives the cooling fan motor is precisely controlled by pulse width modulation (PWM).</li>
		<li>Prepare a series of wild type E. coli samples with optical densities at 600 nm typically ranging from 0.07 to 0.3 for calibration. Place a test E. coli sample in the culture vial and record the photodetector voltage.
		<ol>
			<li>Place ~100 &#181;l of the same sample in the plate reader and record the optical density. Use the photodetector voltage versus optical density data to plot the calibration curve. Note that typically, one unit change in optical density corresponds to ~7.6 V change in the photodetector with the bias scheme used here.</li>
		</ol>
		</li>
	</ol>
	</li>
</ol>
2. Running the Morbidostat
<ol>
	<li>Preparation Before Starting the Daily Experiment
	<ol>
		<li>Prepare the culture vial with three ultra-chemical resistant Tygon tubings with inner diameter 1/32 inch and outer diameter 3/32 inch for inlets to form the device as in section 1.1 and in Supplementary Figure 1.</li>
		<li>Prepare the M9 minimal medium (0.2% glucose) and trimethoprim (TMP) drug containing medium. Sterilize the medium, the medium bottle, the drug medium bottle, the waste bottle, and the culture vial in an autoclave at 121 &#176;C. 
		NOTE: The TMP is a stock solution that is used to later achieve the concentrations in Table 1 and the TMP drug containing medium is not autoclaved.</li>
	</ol>
	</li>
	<li>Running the Morbidostat
	<ol>
		<li>On the first day of the experiment, thaw 1 ml of frozen wild type E. coli MG1655 cells for 5 min at room temperature and transfer 120 &#181;l of the cells to the culture vial containing ~12 ml of M9 growth medium. After the first day, thaw 1 ml of frozen E. coli cells from the previous day for 5 min and transfer 120 &#181;l of the cells to a new culture vial containing ~12 ml of M9 growth medium.</li>
		<li>Turn on the shaker incubator and set the temperature to 30 &#176;C with no shaking.</li>
		<li>Start the morbidostat operation by turning on the micro-pump, the magnetic stirring unit, and the optical density measurement. 
		NOTE: During the operation, a feedback threshold algorithm is used to control the drug injection. When the measured optical density exceeds a preset threshold, the drug injection pump would be turned on and the medium pump would be turned off. Otherwise, the drug injection pump remains off and the medium pump is on.</li>
		<li>Monitor the voltage from time to time to ensure there is microbial growth. 
		Note: Because of the freeze and thaw cycle, E. coli cells exhibit a delay of ~4 hr during each day&#39;s growth.</li>
		<li>After ~23 hr, stop the micro-pump by turning off its supply voltage and take out the culture vial. Add 15% glycerol into the culture vial and freeze the sample at -80 &#176;C for storage.</li>
		<li>Repeat steps 2.2.1 to 2.2.5.</li>
	</ol>
	</li>
</ol>
3. Antibiotic Susceptibility Measurement in 96 Well Format
NOTE: Perform the growth rate measurement in a plate reader with a 96 well format to determine the antibiotic resistance level.
<ol>
	<li>Thaw the daily frozen sample at room temperature for 5 min and transfer 15 &#181;l of the cell to the culture vial containing ~15 ml M9 medium. Allow them to grow until the optical density at 600 nm reaches ~0.1. Divide the 15 ml into 1 ml bottles and add the TMP drug at this step to obtain the desired drug concentrations as shown in Table 1.</li>
	<li>Take 200 &#181;l of the sample from step 3.1 and place into each well in the plate reader and allow them to grow for 12 hr5. The optical density at wavelength 600 nm is recorded automatically during the measurement. 
	NOTE: For each data point, triplicate measurements are recorded and averaged to ensure the consistency of the data. The data on optical density versus time can be used to obtain the growth rate.</li>
	<li>Plot the growth rate data versus the drug concentration to obtain IC50. Note that IC50 is defined as the drug concentration at which the growth rate is fifty percent of the maximal growth rate5.</li>
</ol>
4. Single Cell Morphology and Antibiotic Susceptibility Measurement in Microfluidic Devices
<ol>
	<li>Perform fabrication of the microfluidic devices via multilayer soft lithography from PDMS as described elsewhere15.
	<ol>
		<li>Use photolithography to make the photoresist mold for the control and flow layers. Note that for the control layer, use negative photoresist (~15 &#181;m height) and positive photoresist (~8 &#181;m height) to produce a mold on a bare silicon wafer.</li>
		<li>Prepare PDMS mixtures with cross linking ratios of 5:1 and 20:1 for the control layer and the flow layer, respectively. Put the mixtures into a desiccator under vacuum to remove any bubbles, for 1 hr.</li>
		<li>Expose the control layer photoresist molds on silicon wafer to trimethylchlorosilane (TMCS) vapor. Make the control layer of ~6 mm thickness by casting the PDMS mixture (with cross linking ratio 5:1) on the silicon wafer on the control layer photoresist mold. Bake the control layer for 40 min at 80 &#176;C for 1 hr in the oven.</li>
		<li>Make the flow layer by spin coating a PDMS mixture (with cross linking ratio 20:1, spin speed 3,000 rpm for 60 sec) on a flow layer photoresist mold. Bake the flow layer for 30 min at 80 &#176;C for 1 hr in the oven.</li>
		<li>Use a razor blade to cut the control layer into the desired chip size (typically 3 cm x 2 cm) and manually peel off the control layer. Place the control layer on top of the flow layer and align them under a stereomicroscope. Cure the aligned assembly at 80 &#176;C in the oven overnight. Afterwards, soak the assembly in 250 ml of deionized water in a plastic container for 5 hr to dissolve the residual TMCS.</li>
		<li>Subsequently, punch the inlet holes with 20 G needles and bond the entire elastomer to a glass slide coated with a blank PDMS layer (PDMS cross linking ratio 5:1, spin speed 2,000 rpm for 30 sec) by air plasma treatment for 40 sec at 1.2 Torr air pressure.</li>
		<li>Carry out extensive baking for 36 hr at 80 &#176;C to reduce the cytotoxic effects from PDMS. Note that this baking step is critical to minimize the toxicity to the bacterial cells.</li>
	</ol>
	</li>
	<li>On Chip Growth Experiment
	<ol>
		<li>Before loading into the microfluidic device, flush it with deionized water for 1 hr and M9 medium for 1 hr.</li>
		<li>Thaw the daily frozen sample at room temperature for 5 min and inoculate a new test tube with fresh M9 medium. Place the sample in a shaker incubator at 37 &#176;C overnight.</li>
		<li>Dilute the microbial sample 10 fold with M9 medium and load it into the microfluidic device by pressuring the microbial sample container at 5 psi. Then load the TMP drug medium into the chip by pressuring the drug medium container at 5 psi. Execute the mixing between the microbe and drug by actuating the micromechanical valve between the two chambers on the microfluidic chip for 15 min.</li>
		<li>Place the microfluidic chip in the microscope incubator mounted on the inverted microscope. Acquire the cell image in the growth chamber every hr for 8 hr with the CCD camera mounted on the inverted microscope.</li>
		<li>Use the custom program script to calculate the cell numbers through a threshold algorithm on the cell image data18. Note that the cell number data are averaged typically over three microfluidic chambers.</li>
	</ol>
	</li>
</ol>

<ol>
	<li>Levy, S. B., Marshall, B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Antibiotic+resistance+worldwide:+causes,+challenges,+and+responses.">Antibiotic resistance worldwide: causes, challenges, and responses.</a> Nat. Med. 10, s122-s129 (2004).</li><li>Wang, M. M., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tracking+the+in+vivo+evolution+of+multidrug+resistance+in+Staphylococus+aureus+by+whole+genome+sequencing.">Tracking the in vivo evolution of multidrug resistance in Staphylococus aureus by whole genome sequencing.</a> Pro. Natl. Acad. Sci. 104, 9451 (2007).</li><li>Dragosits, M., Mattanovich, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Adaptive+laboratory+evolution+-+principles+and+applications+for+biotechnology.">Adaptive laboratory evolution - principles and applications for biotechnology.</a> Microbial Cell Factory. 12, 64 (2013).</li><li>Zhang, Q., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Acceleration+of+emergence+of+bacterial+antibiotic+resistance+in+connected+microenvironment.">Acceleration of emergence of bacterial antibiotic resistance in connected microenvironment.</a> Science. 333, 1764-1767 (2011).</li><li>Toprak, E., Veres, A., Michel, J. B., Chait, R., Hartl, D. L., Kishony, R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Evolutionary+paths+to+antibiotic+resistance+under+dynamically+sustained+drug+selection.">Evolutionary paths to antibiotic resistance under dynamically sustained drug selection.</a> Nature Genetics. 44, 101-106 (2012).</li><li>Toprak, E., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Building+a+morbidostast:+an+automated+continuous+culture+device+for+studying+bacterial+drug+resistance+under+dynamically+sustained+drug+inhibition.">Building a morbidostast: an automated continuous culture device for studying bacterial drug resistance under dynamically sustained drug inhibition.</a> Nature Protocol. 8, 555-567 (2013).</li><li>Rosenthal, A. Z., Elowitz, M. B. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Following+evolution+of+bacterial+antibiotic+resistance+in+real+time.">Following evolution of bacterial antibiotic resistance in real time.</a> Nature Genetics. 44, 11-13 (2012).</li><li>Young, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=In+vitro+antibacterial+resistance+selection+and+quantitation.">In vitro antibacterial resistance selection and quantitation.</a> Curr Protoc Pharmacol. , (2006).</li><li>Novick, A., Szilard, L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Experiments+with+the+Chemostat+on+spontaneous+mutations+of+bacteria.">Experiments with the Chemostat on spontaneous mutations of bacteria.</a> Proc. Natl. Acad. Sci. U.S.A. 36, 708-719 (1950).</li><li>Balagadde, F. K., You, L., Hansen, C. L., Arnold, F. H., Quake, S. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Long-term+monitoring+of+bacteria+undergoing+programmed+population+control+in+a+microchemostat.">Long-term monitoring of bacteria undergoing programmed population control in a microchemostat.</a> Science. 309, 137-140 (2005).</li><li>Groisman, A., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+microfluidic+chemostat+for+experiments+with+bacterial+and+yeast+cells.">A microfluidic chemostat for experiments with bacterial and yeast cells.</a> Nat. Methods. 2, 685-689 (2005).</li><li>Miller, A. W., Befort, C., Kerr, E. O., Dunham, M. J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Design+and+Use+of+Multiplexed+Chemostat+Arrays.">Design and Use of Multiplexed Chemostat Arrays.</a> J. Vis. Exp. (72), e50262 (2013).</li><li>Takahashi, C. N., Miller, A. W., Ekness, F., Dunham, M. J., Klavins, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+low+cost,+customizable+turbidostat+for+use+in+synthetic+circuit+characterization.">A low cost, customizable turbidostat for use in synthetic circuit characterization.</a> ACS Synthetic Biology. , (2015).</li><li>Mohan, R., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+multiplexed+microfluidic+platform+for+rapid+antibiotic+susceptibility+testing.">A multiplexed microfluidic platform for rapid antibiotic susceptibility testing.</a> Biosens Bioelectrons. 49, 118-125 (2013).</li><li>Unger, M. A., Chou, H. P., Thorsen, T., Scherer, A., Quake, S. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Monolithic+microfabricated+valves+and+pumps+by+multilayer+soft+lithography.">Monolithic microfabricated valves and pumps by multilayer soft lithography.</a> Science. 288, 113-116 (2000).</li><li>Kellogg, R. A., Gomez-Sjoberg, R., Leyrat, A. A., Tay, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Nat. Protocols. 9, 1713 (2014).</li><li>Gu, G. Y., Lee, Y. W., Chiang, C. C., Yang, Y. T. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+nanoliter+microfluidic+serial+dilution+bioreactor.">A nanoliter microfluidic serial dilution bioreactor.</a> Biomicrofluidics. 9, 044126 (2015).</li><li>Gonzalez, R. C., Woods, R. E., Eddins, S. L. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=.">.</a> Digital image using Matlab processing. , (2004).</li><li>Heikkila, E., Sundstrom, L., Huovinen, P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Trimethoprim+resistance+in+Escherichia+coli+isolates+from+a+geriatric+unit.">Trimethoprim resistance in Escherichia coli isolates from a geriatric unit.</a> Antimicrob. Agents Chemother. 34, 2013-2015 (1990).</li><li>Flensburg, J., Skold, O. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Massive+overproduction+of+dihydrofolate+reductase+in+bacteria+as+a+response+to+the+use+of+trimethoprim.">Massive overproduction of dihydrofolate reductase in bacteria as a response to the use of trimethoprim.</a> Eur. J. Biochem. 162, 473-476 (1987).</li><li>Ohmae, E., Sasaki, Y., Gekko, K. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Effects+of+five-tryptophan+mutations+on+structure,+stability+and+function+of+Escherichia+coli+dihydrofolate+reductase.">Effects of five-tryptophan mutations on structure, stability and function of Escherichia coli dihydrofolate reductase.</a> J. Biochem. 130, 439-447 (2001).</li><li>Smith, D. R., Calvo, J. M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Nucleotide+sequence+of+dihydrofolate+reductase+genes+from+trimethoprim-resistant+mutants+of+Escherichia+coli.+Evidence+that+dihydrofolate+reductase+interacts+with+another+essential+gene+product.">Nucleotide sequence of dihydrofolate reductase genes from trimethoprim-resistant mutants of Escherichia coli. Evidence that dihydrofolate reductase interacts with another essential gene product.</a> Mol. Gen. Genet. 187, 72-78 (1982).</li><li>Okumus, B., Yildiz, S., Toprak, E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Fluidic+and+microfluidic+tools+for+quantitative+systems+biology.">Fluidic and microfluidic tools for quantitative systems biology.</a> Curr Opin Biotech. 25, 30-38 (2014).</li><li>Cho, J., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+rapid+antimicrobial+susceptibility+test+based+on+single-cell+morphological+analysis.">A rapid antimicrobial susceptibility test based on single-cell morphological analysis.</a> Sci. Transl. Med. 17, 267 (2014).</li><li>Hsu, S. B., Waltman, P. E. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Analysis+of+a+model+of+two+competitors+in+a+chemostat+with+an+external+inhibitor.">Analysis of a model of two competitors in a chemostat with an external inhibitor.</a> SIAM J. Applied Math. , 528-540 (1992).</li><li>Fu, W., et al. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Maximizing+biomass+productivity+and+cell+density+of+Chlorella+vulgaris+by+using+light-emitting+diode-based+photobioreactor.">Maximizing biomass productivity and cell density of Chlorella vulgaris by using light-emitting diode-based photobioreactor.</a> J. Biotech. 161, 242-249 (2012).</li><li>Peabody, V. G. L., Winkler, J., Kao, K. C. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Tools+for+developing+tolerance+to+toxic+chemicals+in+microbial+systems+and+perspectives+on+moving+the+field+forward+and+into+the+industrial+setting.">Tools for developing tolerance to toxic chemicals in microbial systems and perspectives on moving the field forward and into the industrial setting.</a> Curr Opin in Chem Eng. 6, 9-17 (2014).</li></ol>

The authors have nothing to disclose.

A low-footprint morbidostat device from low-cost components is demonstrated. The increases in drug resistance level registered by the device are consistent with those of previous reports5. Designed for evolutionary studies of drug resistance, the device is potentially applicable to many other experiments. First, a comprehensive database of drug-induced mutations can be established for a large set of clinically relevant antibiotics. For example, the evolutionary pathway of multiple drug resistance can be studie...

Since the introduction of the first antibiotic drug penicillin, microbial antibiotic resistance has developed into a global health problem1. Although the acquisition of antibiotic resistance can be retrospectively studied in vivo, the conditions of these experiments are often not controlled throughout the entire evolution2. Alternatively, adaptive laboratory evolution can reveal the molecular evolution of a microbial species under environmental stresses or selection pressure from an antibiotic drug3. Recently, many well-controlled evolutionary experiments of antibiotic drug resistance have elucidated the emergence of antibiotic drug resistance. For example, Austin&#39;s group demonstrated rapid emergence in a properly engineered microfluidic compartmented environment4. The recently developed morbidostat induces systematic mutations under drug selection pressure5,6. The morbidostat, a microbial selection device that continuously adjusts the antibiotic concentration to maintain a nearly constant population, is a major advance from the fluctuation test used in microbiology7,8. In the fluctuation test, an antibiotic drug is injected at high concentration, and the surviving mutants are screened and counted. Instead, microbes in a morbidostat are constantly challenged and acquire multiple mutations.
The morbidostat operates similarly to the chemostat, a culture device invented by Novick and Szliard in 1950 that maintains a constant population by continuously supplying nutrients while diluting the microbial population9. Since its introduction, the chemostat has been advanced and improved. Current microfluidic chemostats have reached nanoliter and single-cell capacities. However, these devices are unsuitable for adaptive evolution experiments, which require a large cell population with many mutation events10,11. Recently, mini-chemostats with working volumes of ~10 ml have also been developed to fill in the gap between liter scale bioreactors and the microfluidic chemostat12,13.
Here we present the design and use of a low-cost, automated morbidostat for an antibiotic drug resistance study. The proposed module can be employed in a shaker incubator in a microbiology laboratory with minimal hardware requirement. The open-source firmware is also easily tailored to specific applications of adaptive evolution, such as metabolic engineering3. Finally, the morbidostat is integrated into a multiplexed microfluidic platform for antibiotic susceptibility testing14.

<table><tbody><tr><td>Environmental Shaker Incubator</td><td>BioSan</td><td>ES-20</td><td></td></tr><tr><td>Arduino Leonardo board</td><td>Arduino</td><td>Leonardo</td><td></td></tr><tr><td>680 Ohm Carbon Resistor</td><td>Digikey</td><td></td><td>Bias resistor for LED</td></tr><tr><td>100k Ohm Carbon resistor</td><td>Digikey</td><td></td><td>Bias resistor for phototransistor</td></tr><tr><td>940 nm light emitting diode</td><td>Bright LED Electronic</td><td>BIR-BM13E4G-2</td><td>Optical density measurement</td></tr><tr><td>940 nm phototransistor</td><td>Kodenshi&amp;nbsp;</td><td>ST-2L2B</td><td>Optical density measurement</td></tr><tr><td>Darlington pair IC Toshiba</td><td>Mouser</td><td>ULN2803APG</td><td>this IC drives micropumps and magnetic stirring unit</td></tr><tr><td>5 V DC brushless fan</td><td>ADDA</td><td>AD0405LX-G70</td><td>spec: 5 V supply voltage and 80&amp;nbsp;mA; available www.jameco.com</td></tr><tr><td>Piezoelectric micropump</td><td>CurieJet</td><td>PS15I-FT-5L</td><td>Pressure &gt; 3&amp;nbsp;kPa; Flow rate &gt;5 ml/min</td></tr><tr><td>Tygon 3350 Tuning</td><td>Saint Gobain</td><td>ABW00001</td><td>ID: 1/32&quot; OD: 3/32&quot; L:50&#039;&amp;nbsp;</td></tr><tr><td>Magnetic Stir bar</td><td>COWIE</td><td></td><td>tapered shape dim: 10&amp;nbsp;mm x 4 mm</td></tr><tr><td>Glass scintillation 20 ml vial</td><td>DGS</td><td></td><td>Pyrex glass 28 mm (diameter) x 61 mm (height)</td></tr><tr><td>Culture vial holder</td><td></td><td></td><td>Custom made from Polyformaldehyde&amp;nbsp;</td></tr><tr><td>Silicone</td><td>Dow Corning</td><td>Sylgald 184</td><td>used to seal the glass vial</td></tr><tr><td>Medium bottle</td><td>VWR</td><td>66022-065</td><td></td></tr><tr><td>Difco M9 minimal salt 5x</td><td>BD</td><td></td><td>Medium</td></tr><tr><td>Cadamino Acid</td><td>BD</td><td></td><td>Medium</td></tr><tr><td>glucose</td><td>Sigma</td><td></td><td></td></tr><tr><td>Agar Bateriological</td><td>Oxoid</td><td></td><td>for agar plate</td></tr><tr><td>Luria Bertani medium</td><td></td><td></td><td></td></tr><tr><td>Inverted microscope</td><td>Leica Microsystems</td><td>Leica DMI-LED</td><td>used for microfluidic measurement Use 40X objective NA = 0.55</td></tr><tr><td>Microscope Incubator</td><td>Live Cell Instrument</td><td>CU-109</td><td>used for microfluidic measurement</td></tr><tr><td>Solenoidal valves</td><td>Pneumadyne</td><td>S10MM-31-12-3</td><td>Normally open 1.3 Watt 12 Vdc</td></tr><tr><td>USB interface card</td><td>Hobby Engineering</td><td>USBIO24-R Digital I/O Module&amp;nbsp;</td><td>for microfluidics measurement</td></tr><tr><td>Air compressor</td><td>Rocker Scientific</td><td>ROCKER 440</td><td>Pressure source for microfluidcs; Max. Pressure 80 psi</td></tr><tr><td>Male luer-lock fittings to 1/8&quot; barb</td><td>ValuePlastics.com</td><td>MTLL230-1</td><td>used for microfluidic control</td></tr><tr><td>1/8&quot; barb to 10-32 threaded port</td><td>ValuePlastics.com</td><td>B-1</td><td>used for microfluidic control</td></tr><tr><td>Female luer-lock fittings to 10-32 threaded port</td><td>ValuePlastics.com</td><td>KFTL-1</td><td>used for microfluidic control</td></tr><tr><td>NPN darlington transistor 500 mA, 40&amp;nbsp;V (2N6427)</td><td>DigiKey.com</td><td>2N6427GOS-ND</td><td>used for microfluidic control</td></tr><tr><td>10 kOhm, carbon film resistor, 0.25 W</td><td>DigiKey.com</td><td>P10KBACT-ND</td><td>used for microfluidic control</td></tr><tr><td>Tantalum capacitor, 10&amp;nbsp;&amp;mu;F, 25 V, 10%</td><td>DigiKey.com</td><td>478-1841-ND</td><td>used for microfluidic control</td></tr><tr><td>Andor CCD camera</td><td>Andor</td><td>Zyla 4.2 Plus SCMOS</td><td>used for microfluidic on chip imaging</td></tr><tr><td>ELISA plate reader</td><td></td><td></td><td></td></tr><tr><td>two component Silicone&amp;nbsp;</td><td>Momentive</td><td>RTV 615</td><td>used for microfluidic chip fabrication</td></tr><tr><td>SU-8 photoresist</td><td>Micrchem</td><td>SU8 2015</td><td>used for microfluidic chip fabrication</td></tr><tr><td>AZ4620 photoresist</td><td>Clariant</td><td>AZ 4620</td><td>used for microfluidic chip fabrication</td></tr><tr><td>Plasma cleaner</td><td>Harrick Plasma</td><td>PDC 32G</td><td>used for microfluidic chip fabrication</td></tr><tr><td>20 Gauge Syringe Needle</td><td>BD</td><td></td><td>used for microfluidic chip fabrication</td></tr><tr><td>Labcycler</td><td>Sensoquest</td><td>Labcycler</td><td>PCR</td></tr><tr><td>DNA polymerase</td><td>Toyobo</td><td>KDO Plus</td><td>PCR amplification</td></tr><tr><td>Trimethoprim</td><td>Sigma</td><td></td><td></td></tr><tr><td>Plate reader</td><td>Biotek</td><td>Synergy H1 hybrid&amp;nbsp;</td><td>antibiotic resistane measurement</td></tr></tbody></table>

design and use of a low cost, automated morbidostat for adaptive evolution of bacteria under antibiotic drug selection

We describe a low cost, configurable morbidostat for characterizing the evolutionary pathway of antibiotic resistance. The morbidostat is a bacterial culture device that continuously monitors bacterial growth and dynamically adjusts the drug concentration to constantly challenge the bacteria as they evolve to acquire drug resistance. The device features a working volume of ~10 ml and is fully automated and equipped with optical density measurement and micro-pumps for medium and drug delivery. To validate the platform, we measured the stepwise acquisition of trimethoprim resistance in Escherichia coli MG 1655, and integrated the device with a multiplexed microfluidic platform to investigate cell morphology and antibiotic susceptibility. The approach can be up-scaled to laboratory studies of antibiotic drug resistance, and is extendible to adaptive evolution for strain improvements in metabolic engineering and other bacterial culture experiments.

The above-described morbidostat is schematized in Figure 1. The common morbidostat operations, including experimental evolution, antibiotic susceptibility test and cell morphology checking, were validated in an E. coli MG1655 culture exposed to trimethoprim (TMP), a commonly used antibiotic drug5,6. TMP induces very distinctive stepwise increases in drug resistance, and the mutations are clustered around the dihydrofolate reductase (DHFR) gene. Therefo...

Watch this Scientific Journal Video about Design and Use of a Low Cost, Automated Morbidostat for Adaptive Evolution of Bacteria Under Antibiotic Drug Selection at JoVE.com

Design and Use of a Low Cost, Automated Morbidostat for Adaptive Evolution of Bacteria Under Antibiotic Drug Selection

We describe a low cost, configurable morbidostat that enables the characterization of antibiotic drug resistance by dynamically adjusting the drug concentration. The device can be integrated with a multiplexed microfluidic platform. The approach can be scaled up for laboratory antibiotic drug resistance studies.

We describe a low cost, configurable morbidostat for characterizing the evolutionary pathway of antibiotic resistance. The morbidostat is a bacterial ...

design-use-low-cost-automated-morbidostat-for-adaptive-evolution

Universidad San Sebastian

Research

JoVE Journal

Genetics

9.6K Views.  National Tsing Hua University. We describe a low cost, configurable morbidostat that enables the characterization of antibiotic drug resistance by dynamically adjusting the drug concentration. The device can be integrated with a multiplexed microfluidic platform. The approach can be scaled up for laboratory antibiotic drug resistance studies.

Video: Design and Use of a Low Cost, Automated Morbidostat for Adaptive Evolution of Bacteria Under Antibiotic Drug Selection

Procedure for Adaptive Laboratory Evolution of Microorganisms Using a Chemostat

Natural evolution involves genetic diversity such as environmental change and a selection between small populations. Adaptive laboratory evolution (ALE) refers to the experimental situation in which evolution is observed using living organisms under controlled conditions and stressors; organisms are thereby artificially forced to make evolutionary changes. Microorganisms are subject to a variety of stressors in the environment and are capable of regulating certain stress-inducible proteins to increase their chances of survival. Naturally occurring spontaneous mutations bring about changes in a microorganism's genome that affect its chances of survival. Long-term exposure to chemostat culture provokes an accumulation of spontaneous mutations and renders the most adaptable strain dominant. Compared to the colony transfer and serial transfer methods, chemostat culture entails the highest number of cell divisions and, therefore, the highest number of diverse populations. Although chemostat culture for ALE requires more complicated culture devices, it is less labor intensive once the operation begins. Comparative genomic and transcriptome analyses of the adapted strain provide evolutionary clues as to how the stressors contribute to mutations that overcome the stress. The goal of the current paper is to bring about accelerated evolution of microorganisms under controlled laboratory conditions.

Here, we present a protocol to obtain adaptive laboratory evolution of microorganisms under conditions using chemostat culture. Also, genomic analysis of the evolved strain is discussed.

Natural evolution involves genetic diversity such as environmental change and a selection between small populations. Adaptive laboratory evolution (ALE) ...

Testing the Role of Multicopy Plasmids in the Evolution of Antibiotic Resistance

Multicopy plasmids are extremely abundant in prokaryotes but their role in bacterial evolution remains poorly understood. We recently showed that the increase in gene copy number per cell provided by multicopy plasmids could accelerate the evolution of plasmid-encoded genes. In this work, we present an experimental system to test the ability of multicopy plasmids to promote gene evolution. Using simple molecular biology methods, we constructed a model system where an antibiotic resistance gene can be inserted into Escherichia coli MG1655, either in the chromosome or on a multicopy plasmid. We use an experimental evolution approach to propagate the different strains under increasing concentrations of antibiotics and we measure survival of bacterial populations over time. The choice of the antibiotic molecule and the resistance gene is so that the gene can only confer resistance through the acquisition of mutations. This &#34;evolutionary rescue&#34; approach provides a simple method to test the potential of multicopy plasmids to promote the acquisition of antibiotic resistance. In the next step of the experimental system, the molecular bases of antibiotic resistance are characterized. To identify mutations responsible for the acquisition of antibiotic resistance we use deep DNA sequencing of samples obtained from whole populations and clones. Finally, to confirm the role of the mutations in the gene under study, we reconstruct them in the parental background and test the resistance phenotype of the resulting strains.

Here we present an experimental method to test the role of multicopy plasmids in the evolution of antibiotic resistance.

Multicopy plasmids are extremely abundant in prokaryotes but their role in bacterial evolution remains poorly understood. We recently showed that the ...

Designing Automated, High-throughput, Continuous Cell Growth Experiments Using eVOLVER

Continuous culture methods enable cells to be grown under quantitatively controlled environmental conditions, and are thus broadly useful for measuring fitness phenotypes and improving our understanding of how genotypes are shaped by selection. Extensive recent efforts to develop and apply niche continuous culture devices have revealed the benefits of conducting new forms of cell culture control. This includes defining custom selection pressures and increasing throughput for studies ranging from long-term experimental evolution to genome-wide library selections and synthetic gene circuit characterization. The eVOLVER platform was recently developed to meet this growing demand: a continuous culture platform with a high degree of scalability, flexibility, and automation. eVOLVER provides a single standardizing platform that can be (re)-configured and scaled with minimal effort to perform many different types of high-throughput or multi-dimensional growth selection experiments. Here, a protocol is presented to provide users of the eVOLVER framework a description for configuring the system to conduct a custom, large-scale continuous growth experiment. Specifically, the protocol guides users on how to program the system to multiplex two selection pressures &#8212; temperature and osmolarity &#8212; across many eVOLVER vials in order to quantify fitness landscapes of Saccharomyces cerevisiae mutants at fine resolution. We show how the device can be configured both programmatically, through its open-source web-based software, and physically, by arranging fluidic and hardware layouts. The process of physically setting up the device, programming the culture routine, monitoring and interacting with the experiment in real-time over the internet, sampling vials for subsequent offline analysis, and post experiment data analysis are detailed. This should serve as a starting point for researchers across diverse disciplines to apply eVOLVER in the design of their own complex and high-throughput cell growth experiments to study and manipulate biological systems.

The eVOLVER framework enables high-throughput continuous microbial culture with high resolution and dynamic control over experimental parameters. This protocol demonstrates how to apply the system to conduct a complex fitness experiment, guiding users on programming automated control over many individual cultures, measuring, collecting, and interacting with experimental data in real-time.

Continuous culture methods enable cells to be grown under quantitatively controlled environmental conditions, and are thus broadly useful for measuring ...

Quantification of Plasmid-Mediated Antibiotic Resistance in an Experimental Evolution Approach

Plasmids play a major role in microbial ecology and evolution as vehicles of lateral gene transfer and reservoirs of accessory gene functions in microbial populations. This is especially the case under rapidly changing environments such as fluctuating antibiotics exposure. We recently showed that plasmids maintain antibiotic resistance genes in Escherichia coli without positive selection for the plasmid presence. Here we describe an experimental system that allows following both the plasmid genotype and phenotype in long-term evolution experiments. We use molecular techniques to design a model plasmid that is subsequently introduced to an experimental evolution batch system approach in an E. coli host. We follow the plasmid frequency over time by applying replica plating of the E. coli populations while quantifying the antibiotic resistance persistence. In addition, we monitor the conformation of plasmids in host cells by analyzing the extent of plasmid multimer formation by plasmid nicking and agarose gel electrophoresis. Such an approach allows us to visualize not only the genome size of evolving plasmids but also their topological conformation-a factor highly important for plasmid inheritance. Our system combines molecular strategies with traditional microbiology approaches and provides a set-up to follow plasmids in bacterial populations over a long time. The presented approach can be applied to study a wide range of mobile genetic elements in the future.

Our experimental approach provides a strategy to follow plasmid abundance and antibiotic resistance over time in bacterial populations.

Plasmids play a major role in microbial ecology and evolution as vehicles of lateral gene transfer and reservoirs of accessory gene functions in microbial ...

Daily Transfers, Archiving Populations, and Measuring Fitness in the Long-Term Evolution Experiment with Escherichia coli

The Long-Term Evolution Experiment (LTEE) has followed twelve populations of Escherichia coli as they have adapted to a simple laboratory environment for more than 35 years and 77,000 bacterial generations. The setup and procedures used in the LTEE epitomize reliable and reproducible methods for studying microbial evolution. In this protocol, we first describe how the LTEE populations are transferred to fresh medium and cultured each day. Then, we describe how the LTEE populations are regularly checked for possible signs of contamination and archived to provide a permanent frozen "fossil record" for later study. Multiple safeguards included in these procedures are designed to prevent contamination, detect various problems when they occur, and recover from disruptions without appreciably setting back the progress of the experiment. One way that the overall tempo and character of evolutionary changes are monitored in the LTEE is by measuring the competitive fitness of populations and strains from the experiment. We describe how co-culture competition assays are conducted and provide both a spreadsheet and an R package (fitnessR) for calculating relative fitness from the results. Over the course of the LTEE, the behaviors of some populations have changed in interesting ways, and new technologies like whole-genome sequencing have provided additional avenues for investigating how the populations have evolved. We end by discussing how the original LTEE procedures have been updated to accommodate or take advantage of these changes. This protocol will be useful for researchers who use the LTEE as a model system for studying connections between evolution and genetics, molecular biology, systems biology, and ecology. More broadly, the LTEE provides a tried-and-true template for those who are beginning their own evolution experiments with new microbes, environments, and questions.

Daily Transfers, Archiving Populations, and Measuring Fitness in the Long-Term Evolution Experiment with Escherichia coli

This protocol describes how to maintain the Escherichia coli Long-Term Evolution Experiment (LTEE) by performing its daily transfers and periodic freeze-downs and how to conduct competition assays to measure fitness improvements in evolved bacteria. These procedures can serve as a template for researchers starting their own microbial evolution experiments.

The Long-Term Evolution Experiment (LTEE) has followed twelve populations of Escherichia coli as they have adapted to a simple laboratory environment for ...

Mutagenesis and Functional Selection Protocols for Directed Evolution of Proteins in E. coli

The efficient generation of genetic diversity represents an invaluable molecular tool that can be used to label DNA synthesis, to create unique molecular signatures, or to evolve proteins in the laboratory. Here, we present a protocol that allows the generation of large (>1011) mutant libraries for a given target sequence. This method is based on replication of a ColE1 plasmid encoding the desired sequence by a low-fidelity variant of DNA polymerase I (LF-Pol I). The target plasmid is transformed into a mutator strain of E. coli and plated on solid media, yielding between 0.2 and 1 mutations/kb, depending on the location of the target gene. Higher mutation frequencies are achieved by iterating this process of mutagenesis. Compared to alternative methods of mutagenesis, our protocol stands out for its simplicity, as no cloning or PCR are involved. Thus, our method is ideal for mutational labeling of plasmids or other Pol I templates or to explore large sections of sequence space for the evolution of activities not present in the original target. The tight spatial control that PCR or randomized oligonucleotide-based methods offer can also be achieved through subsequent cloning of specific sections of the library. Here we provide protocols showing how to create a random mutant library and how to establish drug-based selections in E. coli to identify mutants exhibiting new biochemical activities.

Mutagenesis and Functional Selection Protocols for Directed Evolution of Proteins in E. coli

Here we demonstrate a simple protocol to create a random mutant library for a given target sequence. We show how this method, which is performed in vivo in Escherichia coli, can be coupled with functional selections to evolve new enzymatic activities.

The efficient generation of genetic diversity represents an invaluable molecular tool that can be used to label DNA synthesis, to create unique molecular ...

Biology

The Use of Chemostats in Microbial Systems Biology

Cells regulate their rate of growth in response to signals from the external world. As the cell grows, diverse cellular processes must be coordinated including macromolecular synthesis, metabolism and ultimately, commitment to the cell division cycle. The chemostat, a method of experimentally controlling cell growth rate, provides a powerful means of systematically studying how growth rate impacts cellular processes - including gene expression and metabolism - and the regulatory networks that control the rate of cell growth. When maintained for hundreds of generations chemostats can be used to study adaptive evolution of microbes in environmental conditions that limit cell growth. We describe the principle of chemostat cultures, demonstrate their operation and provide examples of their various applications. Following a period of disuse after their introduction in the middle of the twentieth century, the convergence of genome-scale methodologies with a renewed interest in the regulation of cell growth and the molecular basis of adaptive evolution is stimulating a renaissance in the use of chemostats in biological research.

Cell growth rate is a regulated process and a primary determinant of cell physiology. Continuous culturing using chemostats enables extrinsic control of cell growth rate by nutrient limitation facilitating the study of molecular networks that control cell growth and how those networks evolve to optimize cell growth.

Cells regulate their rate of growth in response to signals from the external world. As the cell grows, diverse cellular processes must be coordinated ...

Design and Use of Multiplexed Chemostat Arrays

Chemostats are continuous culture systems in which cells are grown in a tightly controlled, chemically constant environment where culture density is constrained by limiting specific nutrients.1,2 Data from chemostats are highly reproducible for the measurement of quantitative phenotypes as they provide a constant growth rate and environment at steady state. For these reasons, chemostats have become useful tools for fine-scale characterization of physiology through analysis of gene expression3-6 and other characteristics of cultures at steady-state equilibrium.7 Long-term experiments in chemostats can highlight specific trajectories that microbial populations adopt during adaptive evolution in a controlled environment. In fact, chemostats have been used for experimental evolution since their invention.8 A common result in evolution experiments is for each biological replicate to acquire a unique repertoire of mutations.9-13 This diversity suggests that there is much left to be discovered by performing evolution experiments with far greater throughput. 
We present here the design and operation of a relatively simple, low cost array of miniature chemostats&mdash;or ministats&mdash;and validate their use in determination of physiology and in evolution experiments with yeast. This approach entails growth of tens of chemostats run off a single multiplexed peristaltic pump. The cultures are maintained at a 20 ml working volume, which is practical for a variety of applications. It is our hope that increasing throughput, decreasing expense, and providing detailed building and operation instructions may also motivate research and industrial application of this design as a general platform for functionally characterizing large numbers of strains, species, and growth parameters, as well as genetic or drug libraries.

We developed and validated a small-footprint array of miniature chemostats built from readily available parts for low cost. Physiological and experimental evolution results were similar to larger volume chemostats. The ministat array provides a compact, inexpensive, and accessible platform for traditional chemostat experiments, functional genomics, and chemical screening applications.

Chemostats are continuous culture systems in which cells are grown in a tightly controlled, chemically constant environment where culture density is ...

An Automated Culture System for Use in Preclinical Testing of Host-Directed Therapies for Tuberculosis

Mycobacterium tuberculosis (Mtb), the causative agent of tuberculosis (TB), was the most significant infectious disease killer globally until the advent of COVID-19. Mtb has evolved to persist in its intracellular environment, evade host defenses, and has developed resistance to many anti-tubercular drugs. One approach to solving resistance is identifying existing&#160;approved drugs that will boost the host immune response to Mtb. These drugs could then be repurposed as adjunctive host-directed therapies (HDT) to shorten treatment time and help overcome antibiotic resistance.
Quantification of intracellular Mtb growth in macrophages is a crucial aspect of assessing potential HDT. The gold standard for measuring Mtb growth is counting colony-forming units (CFU) on agar plates. This is a slow, labor-intensive assay that does not lend itself to rapid screening of drugs. In this protocol, an automated, broth-based culture system, which is more commonly used to detect Mtb in clinical specimens, has been adapted for preclinical screening of host-directed therapies. The capacity of the liquid culture assay system to investigate intracellular Mtb growth in macrophages treated with HDT was evaluated. The HDTs tested for their ability to inhibit Mtb growth were all-trans Retinoic acid (AtRA), both in solution and encapsulated in poly(lactic-co-glycolic acid) (PLGA) microparticles and the combination of interferon-gamma and linezolid. The advantages of this automated liquid culture-based technique over the CFU method include simplicity of setup, less labor-intensive preparation, and faster time to results (5-12 days compared to 21 days or more for agar plates).

Rapid and efficient quantification of intracellular M. tuberculosis growth is crucial for pursuing improved therapies against tuberculosis (TB). This protocol describes a broth-based colorimetric detection assay using an automated liquid culture system to quantify Mtb growth in macrophages treated with candidate host-directed therapies.

Mycobacterium tuberculosis (Mtb), the causative agent of tuberculosis (TB), was the most significant infectious disease killer globally until the advent ...

Immunology and Infection

Monitoring Intraspecies Competition in a Bacterial Cell Population by Cocultivation of Fluorescently Labelled Strains

Many microorganisms such as bacteria proliferate extremely fast and the populations may reach high cell densities. Small fractions of cells in a population always have accumulated mutations that are either detrimental or beneficial for the cell. If the fitness effect of a mutation provides the subpopulation with a strong selective growth advantage, the individuals of this subpopulation may rapidly outcompete and even completely eliminate their immediate fellows. Thus, small genetic changes and selection-driven accumulation of cells that have acquired beneficial mutations may lead to a complete shift of the genotype of a cell population. Here we present a procedure to monitor the rapid clonal expansion and elimination of beneficial and detrimental mutations, respectively, in a bacterial cell population over time by cocultivation of fluorescently labeled individuals of the Gram-positive model bacterium Bacillus subtilis. The method is easy to perform and very illustrative to display intraspecies competition among the individuals in a bacterial cell population.

Bacteria may accumulate either detrimental or beneficial mutations during their lifetime. In a population of cells individuals that have accumulated beneficial mutations may rapidly outcompete their fellows. Here we present a simple procedure to visualize intraspecies competition in a bacterial cell population over time using fluorescently labeled individuals.&#160;

Design and Use of a Low Cost, Automated Morbidostat for Adaptive Evolution of Bacteria Under Antibiotic Drug Selection

Podsumowanie

Przeglądaj więcej filmów

Rozdziały w tym wideo

Procedure for Adaptive Laboratory Evolution of Microorganisms Using a Chemostat

Testing the Role of Multicopy Plasmids in the Evolution of Antibiotic Resistance

Designing Automated, High-throughput, Continuous Cell Growth Experiments Using eVOLVER

Quantification of Plasmid-Mediated Antibiotic Resistance in an Experimental Evolution Approach

Daily Transfers, Archiving Populations, and Measuring Fitness in the Long-Term Evolution Experiment with Escherichia coli

Mutagenesis and Functional Selection Protocols for Directed Evolution of Proteins in E. coli

The Use of Chemostats in Microbial Systems Biology

Design and Use of Multiplexed Chemostat Arrays

An Automated Culture System for Use in Preclinical Testing of Host-Directed Therapies for Tuberculosis

Monitoring Intraspecies Competition in a Bacterial Cell Population by Cocultivation of Fluorescently Labelled Strains