Name: data acquisition protocol for determining embedded sensitivity functions
Uploaded: 2016-04-20T15:00:00.000+00:00
Duration: 7 min 46 s
Description: Watch this Scientific Journal Video about Data Acquisition Protocol for Determining Embedded Sensitivity Functions at JoVE.com

The authors have no acknowledgements.

1. Pre-test Preparation
<ol>
	<li>Design and fabricate the test fixture. Design the fixture to replicate realistic boundary conditions by choosing bolt locations to match the mounting locations of the blade. Choose steel for the fixture to minimize the contribution from the fixture to the dynamic response of the test specimen.
	<ol>
		<li>Bolt the blade to the custom t-bracket.</li>
		<li>Clamp the fixture to a steel table.</li>
	</ol>
	</li>
	<li>Identify and mark grid of impact locations.
	<ol>
		<li>Choose 30 points that span the entire blade.</li>
		<li>Mark points with a marker or wax pen and number for reference. Measure point spacing using a tape measure for later use in visual representation of results.</li>
	</ol>
	</li>
	<li>Select and calibrate accelerometers.
	<ol>
		<li>Choose single axis, 10 mV/g accelerometers. Be sure to choose accelerometers with the appropriate sensitivity in order to avoid overloading the sensor and to achieve good signal-to-noise ratios. Also, be sure the frequency range of the sensors is sufficient to capture the frequency range of interest for the test specimen.</li>
		<li>Calibrate each sensor.
		<ol>
			<li>Attach the sensor to a hand-held shaker whose output is a single-frequency force with a magnitude of 9.81 m/sec2 rms (i.e., 1 g).</li>
			<li>Measure the response for 2 sec.</li>
			<li>Determine the rms amplitude of the response from the software readout.</li>
			<li>Multiply the rms amplitude by 1,000 to determine the calibration factor for the accelerometer in units of mV/g.</li>
		</ol>
		</li>
	</ol>
	</li>
	<li>Select hammer and hammer tip.
	<ol>
		<li>Choose an impact hammer with a sensitivity of 11.2 mV/N. Be sure to select a hammer that sufficiently excites the test specimen in both amplitude and frequency range.</li>
		<li>Choose a nylon tip. Be sure to select a hammer tip that sufficiently excites the test specimen in both amplitude and frequency range.</li>
		<li>Connect the hammer to the data acquisition system with a BNC cable.</li>
	</ol>
	</li>
	<li>Identify sensor locations and attach sensors (Figure 4).
	<ol>
		<li>Choose locations at points m and n on either side of the damage location.</li>
		<li>Mount a third accelerometer at location k. Data from this sensor will be used to validate the results of the embedded sensitivity function analysis.</li>
		<li>Attach accelerometers using super glue. Allow the super glue to set completely before conducting the impact testing.</li>
	</ol>
	</li>
	<li>Select test parameters in the data acquisition GUI.
	<ol>
		<li>Enable double hit detection.</li>
		<li>Set the sampling frequency to 25,600 Hz. The usable frequency range is, therefore, 12,800 Hz.</li>
		<li>Set the sample time to 1 sec.</li>
		<li>Select the hammer channel as the trigger channel. Set the trigger level to 10 EU.</li>
		<li>Set the pre-trigger length to 5% of the total sample time. The pre-trigger data is data collected before the data acquisition is started that has been stored in a buffer. It is important to retrieve and save this data so that the entire impact event is captured.</li>
		<li>Select the H1 FRF estimator. This estimator assumes that there is noise on the response channels and no noise on the force channel. 
		Note: Do not window data during acquisition. Windows can be applied in post-processing, if necessary.</li>
		<li>Enter accelerometer and hammer information, including calibration factors and identification notes.</li>
		<li>Save settings for record keeping and for use in future tests.</li>
	</ol>
	</li>
</ol>
2. Impact Testing on the Healthy Blade
<ol>
	<li>Impact point 1 with the hammer. When the amplitude of the impact force exceeds the chosen trigger level, the data acquisition system will be triggered and data, including the selected amount of pre-trigger data, will begin recording.
	<ol>
		<li>During data acquisition, monitor channels to avoid channel clipping and double impacts by observing the time histories displayed in the data acquisition software.</li>
		<li>During data acquisition, monitor the coherence for each accelerometer channel to evaluate the quality of the acquired data by observing the coherence plot in the data acquisition software.</li>
	</ol>
	</li>
	<li>Repeat step 2.1 four more times at point 1.
	<ol>
		<li>Use consistent impact amplitudes for all impacts.</li>
	</ol>
	</li>
	<li>Repeat steps 2.1 and 2.2 for all points.</li>
</ol>
3. Impact Testing on the Damaged Blade
<ol>
	<li>Repeat section 2 on the damaged blade in order to collect data for validating the embedded sensitivity function results. Except for the change in the test specimen, all test parameters are kept the same.</li>
</ol>

<ol>
	<li>Singh, N., Joshi, M. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optimization+of+location+and+number+of+sensors+for+structural+health+monitoring+using+genetic+algorithm.">Optimization of location and number of sensors for structural health monitoring using genetic algorithm.</a> Mater Forum. 33, 359-367 (2009).</li><li>Gao, H., Rose, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Ultrasonic+sensor+placement+optimization+in+structural+health+monitoring+using+evolutionary+strategy.">Ultrasonic sensor placement optimization in structural health monitoring using evolutionary strategy.</a> Review Of Qnde. 25, 1687-1693 (2006).</li><li>Raich, A. M., Liszkai, T. R. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Multi-objective+optimization+of+sensor+and+excitation+layouts+for+frequency+response+function-based+structural+damage+identification.">Multi-objective optimization of sensor and excitation layouts for frequency response function-based structural damage identification.</a> Comput-Aided Civinfrastructure Eng. 27 (2), 95-117 (2012).</li><li>Worden, K., Burrows, A. P. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Optimal+sensor+placement+for+fault+detection.">Optimal sensor placement for fault detection.</a> Eng Struct. 23 (8), 885-901 (2001).</li><li>Flynn, E. B., Todd, M. D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Bayesian+approach+to+optimal+sensor+placement+for+structural+health+monitoring+with+application+to+active+sensing.">A Bayesian approach to optimal sensor placement for structural health monitoring with application to active sensing.</a> Mech Syst Signal Pr. 24 (4), 891-903 (2010).</li><li>Markmiller, J., Chang, F. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Sensor+network+optimization+for+a+passive+sensing+impact+detection+technique.">Sensor network optimization for a passive sensing impact detection technique.</a> Struct Health Monit. 9 (1), 25-39 (2010).</li><li>Yang, C., Adams, D., Yoo, S., Kim, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=An+embedded+sensitivity+approach+for+diagnosing+system-level+noise+and+vibration+problems.">An embedded sensitivity approach for diagnosing system-level noise and vibration problems.</a> J. Sound Vibration. 269 (3), 1063-1081 (2004).</li><li>Yang, C., Adams, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Predicting+changes+in+vibration+behavior+using+first-+and+second-order+iterative+embedded+sensitivity+functions.">Predicting changes in vibration behavior using first- and second-order iterative embedded sensitivity functions.</a> J. Sound Vibration. 323 (1), 173-193 (2009).</li><li>Yang, C., Adams, D. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+Damage+Identification+Technique+based+on+Embedded+Sensitivity+Analysis+and+Optimization+Processes.">A Damage Identification Technique based on Embedded Sensitivity Analysis and Optimization Processes.</a> J. Sound Vibration. 333 (14), 3109-3119 (2013).</li><li>Rocklin, G. T., Crowley, J., Vold, H. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=A+comparison+of+the+H1,+H2,+and+Hv+frequency+response+functions.">A comparison of the H1, H2, and Hv frequency response functions.</a> Proc. Of IMAC III. 1, 272-278 (1985).</li><li>Meyer, J., Adams, D., Silvers, J. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Embedded+Sensitivity+Functions+for+improving+the+effectiveness+of+vibro-acoustic+modulation+and+damage+detection+on+wind+turbine+blades.">Embedded Sensitivity Functions for improving the effectiveness of vibro-acoustic modulation and damage detection on wind turbine blades.</a> , (2014).</li><li>Guratzsch, R., Mahadevan, S. <a target="_blank" href="http://www.ncbi.nlm.nih.gov/entrez/query.fcgi?db=PubMed&cmd=Search&doptcmdl=Citation&defaultField=Title+Word&term=Structural+health+monitoring+sensor+placement+optimization+under+uncertainty.">Structural health monitoring sensor placement optimization under uncertainty.</a> AIAA J. 48 (7), 1281-1289 (2010).</li></ol>

The authors have nothing to disclose.

Test fixtures should be designed to replicate realistic boundary conditions so that results will be applicable under operating conditions. The selection of the number of impact points used for testing is a trade-off between having sufficient spatial resolution and the testing time. Select the hammer based on the size of the test specimen and the frequency range of interest. In general, the smaller the hammer, the broader the frequency range excited. However, smaller hammers typically produce lower amplitude forces. Impac...

Many structural health monitoring techniques rely on changes in measured frequency response functions (FRFs) to detect damage within a structure. However, few of these methods address how to determine sensor placements and/or input force locations that will maximize the effectiveness of the method to detect damage. Embedded sensitivity functions (ESFs) can be used to determine the sensitivity of an FRF to a local change in a structure&#39;s material properties. Therefore, because damage typically results in a local change in stiffness, damping, or mass of the structure, ESFs provide a method for determining the best sensor and force locations for FRF-based health monitoring techniques.
The purpose of this video and manuscript is to detail the data acquisition process and best practices for determining ESFs for a structure. The process includes determining various FRFs from modal impact testing, which is performed by exciting a structure with a modal impact hammer and measuring its response with accelerometers. In this work, the structure being tested is a 1.2 m residential-scale wind turbine blade. The goal of the testing and analysis is to identify sensor locations which are most sensitive to damage to the blade. These sensor locations could then be used in a structural health monitoring scheme to monitor the blade for damage.
Besides the use of ESFs to determine the most effective sensor locations to use in a structural health monitoring scheme, several optimal sensor placement algorithms can also be found demonstrated in the literature. In [Kramer], Kramer iteratively evaluates the ability of a set of sensors to observe the modes of a system. More recently, genetic algorithms 1-3 and neural networks 4 have been developed to identify optimal sensor locations. In 5, a Bayesian approach is used that takes into account the risk of different types of errors and the distribution of damage rates. In 6, a finite element model was leveraged to identify the sensor locations most likely to detect damage. In most of the sensor placement algorithms presented in the literature, data from the damaged structure, whether simulated or measured, is required. One advantage of the embedded sensitivity approach is that the sensor locations can be determined from the healthy structure.
Another advantage of ESFs is that material properties need not be explicitly known. Instead, the material properties are &#34;embedded&#34; in the expressions for the system&#39;s FRFs. Therefore, all that is needed to calculate ESFs are a set of measured FRFs at particular input/output locations. Specifically, the sensitivity of the FRF (Hjk) calculated from a response measured at point j to an input at point k, to a change in stiffness (Kmn) between points m and n is
<img alt="Equation1" src="/files/ftp_upload/53690/53690equation1.jpg" />
where <img alt="Equation2" src="/files/ftp_upload/53690/53690equation2.jpg" /> is the ESF as a function of frequency, &#969; 7-9. The procedure for measuring the FRFs required to calculate the right-hand side of equation (1) is detailed in the next section and demonstrated in the video.

<table><tbody><tr><td>Accelerometer</td><td>PCB</td><td>356B11</td><td>three used in testing</td></tr><tr><td>Impact hammer</td><td>PCB</td><td>086C01</td><td></td></tr><tr><td>Data acquisition card</td><td>NI</td><td>9234</td><td></td></tr><tr><td>DAQ chasis&amp;nbsp;</td><td>NI</td><td>cDAQ-9171</td><td>or similar</td></tr><tr><td>Software</td><td>MATLAB</td><td></td><td></td></tr><tr><td>Super glue</td><td>Loctite</td><td>454</td><td></td></tr><tr><td>Handheld Shaker</td><td>PCB</td><td>394C06</td><td>for calibration&amp;nbsp;</td></tr></tbody></table>

data acquisition protocol for determining embedded sensitivity functions

The effectiveness of many structural health monitoring techniques depends on the placement of sensors and the location of input forces. Algorithms for determining optimal sensor and forcing locations typically require data, either simulated or measured, from the damaged structure. Embedded sensitivity functions provide an approach for determining the best available sensor location to detect damage with only data from the healthy structure. In this video and manuscript, the data acquisition procedure and best practices for determining the embedded sensitivity functions of a structure is presented. The frequency response functions used in the calculation of the embedded sensitivity functions are acquired using modal impact testing. Data is acquired and representative results are shown for a residential scale wind turbine blade. Strategies for evaluating the quality of the data being acquired are provided during the demonstration of the data acquisition process.

Figure 1 shows a typical embedded sensitivity function. Similar to an FRF, the ESF has peaks near the natural frequencies of the structure. The higher the value of the ESF, the more sensitive the location is to damage between points m and n. Each of the thirty points tested on the wind turbine blade has a unique ESF. These ESFs can be compared to determine which sensor location would be most sensitive to damage. For example, Figure 2 sho...

Watch this Scientific Journal Video about Data Acquisition Protocol for Determining Embedded Sensitivity Functions at JoVE.com

Data Acquisition Protocol for Determining Embedded Sensitivity Functions

The data acquisition procedure for determining embedded sensitivity functions is described. Data is acquired and representative results are shown for a residential scale wind turbine blade.

The effectiveness of many structural health monitoring techniques depends on the placement of sensors and the location of input forces. Algorithms for ...

data-acquisition-protocol-for-determining-embedded-sensitivity

Universidad San Sebastian

Research

JoVE Journal

Engineering

6.1K Views.  Vanderbilt University. The data acquisition procedure for determining embedded sensitivity functions is described. Data is acquired and representative results are shown for a residential scale wind turbine blade.

Video: Data Acquisition Protocol for Determining Embedded Sensitivity Functions

Combining Multiple Data Acquisition Systems to Study Corticospinal Output and Multi-segment Biomechanics

Transcranial magnetic stimulation techniques allow for an in-depth investigation into the neural mechanisms that underpin human behavior. To date, the use of TMS to study human movement, has been limited by the challenges related to precisely timing the delivery of TMS to features of the unfolding movement and, also, by accurately characterizing kinematics and kinetics. To overcome these technical challenges, TMS delivery and acquisition systems should be integrated with an online motion tracking system. The present manuscript details technical innovations that integrate multiple acquisition systems to facilitate and advance the use of TMS to study human movement. Using commercially available software and hardware systems, a step-by-step approach to both the hardware assembly and the software scripts necessary to perform TMS studies triggered by specific features of a movement is provided. The approach is focused on the study of upper limb, planar, multi-joint reaching movements. However, the same integrative system is amenable to a multitude of sophisticated studies of human motor control.

The use of transcranial magnetic stimulation (TMS) to study human motor control requires the integration of data acquisition systems to control TMS delivery and simultaneously record human behavior. The present manuscript provides a detailed methodology for integrating data acquisition systems for the purpose of investigating human movement via TMS.

Transcranial magnetic stimulation techniques allow for an in-depth investigation into the neural mechanisms that underpin human behavior. To date, the use ...

Behavior

Frequency Mixing Magnetic Detection Scanner for Imaging Magnetic Particles in Planar Samples

The setup of a planar Frequency Mixing Magnetic Detection (p-FMMD) scanner for performing Magnetic Particles Imaging (MPI) of flat samples is presented. It consists of two magnetic measurement heads on both sides of the sample mounted on the legs of a u-shaped support. The sample is locally exposed to a magnetic excitation field consisting of two distinct frequencies, a stronger component at about 77 kHz and a weaker field at 61 Hz. The nonlinear magnetization characteristics of superparamagnetic particles give rise to the generation of intermodulation products. A selected sum-frequency component of the high and low frequency magnetic field incident on the magnetically nonlinear particles is recorded by a demodulation electronics. In contrast to a conventional MPI scanner, p-FMMD does not require the application of a strong magnetic field to the whole sample because mixing of the two frequencies occurs locally. Thus, the lateral dimensions of the sample are just limited by the scanning range and the supports. However, the sample height determines the spatial resolution. In the current setup it is limited to 2 mm. As examples, we present two 20 mm &#215; 25 mm p-FMMD images acquired from samples with 1 &#181;m diameter maghemite particles in silanol matrix and with 50 nm magnetite particles in aminosilane matrix. The results show that the novel MPI scanner can be applied for analysis of thin biological samples and for medical diagnostic purposes.

A scanner for imaging magnetic particles in planar samples was developed using the planar frequency mixing magnetic detection technique. The magnetic intermodulation product response from the nonlinear nonhysteretic magnetization of the particles is recorded upon a two-frequency excitation. It can be used to take 2D images of thin biological samples.

The setup of a planar Frequency Mixing Magnetic Detection (p-FMMD) scanner for performing Magnetic Particles Imaging (MPI) of flat samples is presented. ...

Drug-induced Sensitization of Adenylyl Cyclase: Assay Streamlining and Miniaturization for Small Molecule and siRNA Screening Applications

Sensitization of adenylyl cyclase (AC) signaling has been implicated in a variety of neuropsychiatric and neurologic disorders including substance abuse and Parkinson&#39;s disease. Acute activation of G&#945;i/o-linked receptors inhibits AC activity, whereas persistent activation of these receptors results in heterologous sensitization of AC and increased levels of intracellular cAMP. Previous studies have demonstrated that this enhancement of AC responsiveness is observed both in vitro and in vivo following the chronic activation of several types of G&#945;i/o-linked receptors including D2 dopamine and &#956; opioid receptors. Although heterologous sensitization of AC was first reported four decades ago, the mechanism(s) that underlie this phenomenon remain largely unknown. The lack of mechanistic data presumably reflects the complexity involved with this adaptive response, suggesting that nonbiased approaches could aid in identifying the molecular pathways involved in heterologous sensitization of AC. Previous studies have implicated kinase and Gb&#947; signaling as overlapping components that regulate the heterologous sensitization of AC. To identify unique and additional overlapping targets associated with sensitization of AC, the development and validation of a scalable cAMP sensitization assay is required for greater throughput. Previous approaches to study sensitization are generally cumbersome involving continuous cell culture maintenance as well as a complex methodology for measuring cAMP accumulation that involves multiple wash steps. Thus, the development of a robust cell-based assay that can be used for high throughput screening (HTS) in a 384&#160;well format would facilitate future studies. Using two D2 dopamine receptor cellular models (i.e.&#160;CHO-D2L and HEK-AC6/D2L), we have converted our 48-well sensitization assay (&#62;20 steps 4-5 days) to a five-step, single day assay in 384-well format. This new format is amenable to small molecule screening, and we demonstrate that this assay design can also be readily used for reverse transfection of siRNA in anticipation of targeted siRNA library screening.

Persistent activation of inhibitory G protein-coupled receptors results in sensitization of adenylyl cyclase signaling. To identify the essential molecular pathways, nonbiased approaches are necessary; however, this strategy requires the development of a scalable cell-based cAMP sensitization assay. Herein, we describe a sensitization assay for small molecule and siRNA screening.

Sensitization of adenylyl cyclase (AC) signaling has been implicated in a variety of neuropsychiatric and neurologic disorders including substance abuse ...

Bioengineering

Electric Cell-substrate Impedance Sensing for the Quantification of Endothelial Proliferation, Barrier Function, and Motility

Electric Cell-substrate Impedance Sensing (ECIS) is an in vitro impedance measuring system to quantify the behavior of cells within adherent cell layers. To this end, cells are grown in special culture chambers on top of opposing, circular gold electrodes. A constant small alternating current is applied between the electrodes and the potential across is measured. The insulating properties of the cell membrane create a resistance towards the electrical current flow resulting in an increased electrical potential between the electrodes. Measuring cellular impedance in this manner allows the automated study of cell attachment, growth, morphology, function, and motility. Although the ECIS measurement itself is straightforward and easy to learn, the underlying theory is complex and selection of the right settings and correct analysis and interpretation of the data is not self-evident. Yet, a clear protocol describing the individual steps from the experimental design to preparation, realization, and analysis of the experiment is not available. In this article the basic measurement principle as well as possible applications, experimental considerations, advantages and limitations of the ECIS system are discussed. A guide is provided for the study of cell attachment, spreading and proliferation; quantification of cell behavior in a confluent layer, with regard to barrier function, cell motility, quality of cell-cell and cell-substrate adhesions; and quantification of wound healing and cellular responses to vasoactive stimuli. Representative results are discussed based on human microvascular (MVEC) and human umbilical vein endothelial cells (HUVEC), but are applicable to all adherent growing cells.

This protocol reviews Electric Cell-substrate Impedance Sensing, a method to record and analyze the impedance spectrum of adherent cells for the quantification of cell attachment, proliferation, motility, and cellular responses to pharmacological and toxic stimuli. Detection of endothelial permeability and assessment of cell-cell and cell-substrate contacts are emphasized.

Electric Cell-substrate Impedance Sensing (ECIS) is an in vitro impedance measuring system to quantify the behavior of cells within adherent cell layers. ...

Effective Analysis of Human Exposure Conditions with Body-worn Dosimeters in the 2.4 GHz Band

A well-defined experimental procedure is put forward to evaluate maximum exposure conditions in a worst-case scenario whilst avoiding the uncertainties caused by the use of personal exposimeters (PEMs) as measuring devices: the body shadow effect (BSE), the limited sensitivity range, and the non-identification of the radiation source. An upper bound for exposure levels to EMF in several indoor enclosures has been measured and simulated. The frequency used for the study is 2.4 GHz, as it is the most commonly used band in indoor communications. Although recorded values are well below the International Commission for Non-Ionizing Radiation Protection (ICNIRP) reference levels, there is a particular need to provide reliable exposure levels within particularly sensitive environments. In terms of electromagnetic field (EMF) exposure, limits established in national and international standards for health protection have been set for unperturbed exposure conditions; that is, for real and objective exposure data that have not been altered in any way.

This study describes a protocol to measure exposure levels in the 2.4 GHz band, avoiding the uncertainties caused by the use of personal exposimeters as measuring devices. These alterations of the exposure levels should be taken into account, especially in compliance testing, where exposure limits are defined from non-perturbed data.

A well-defined experimental procedure is put forward to evaluate maximum exposure conditions in a worst-case scenario whilst avoiding the uncertainties ...

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles

Microfluidic processing of biological samples typically involves differential manipulations of suspended particles under various force fields in order to spatially fractionate the sample based on a biological property of interest. For the resultant spatial distribution to be used as the assay readout, microfluidic devices are often subjected to microscopic analysis requiring complex instrumentation with higher cost and reduced portability. To address this limitation, we have developed an integrated electronic sensing technology for multiplexed detection of particles at different locations on a microfluidic chip. Our technology, called Microfluidic CODES, combines Resistive Pulse Sensing with Code Division Multiple Access to compress 2D spatial information into a 1D electrical signal. In this paper, we present a practical demonstration of the Microfluidic CODES technology to detect and size cultured cancer cells distributed over multiple microfluidic channels. As validated by the high-speed microscopy, our technology can accurately analyze dense cell populations all electronically without the need for an external instrument. As such, the Microfluidic CODES can potentially enable low-cost integrated lab-on-a-chip devices that are well suited for the point-of-care testing of biological samples.

We demonstrate a microfluidic platform with an integrated surface electrode network that combines resistive pulse sensing (RPS) with code division multiple access (CDMA), to multiplex detection and sizing of particles in multiple microfluidic channels.

Microfluidic processing of biological samples typically involves differential manipulations of suspended particles under various force fields in order to ...

Characterizing Viscoelastic Properties of 3D-Printed Polymer Metamaterials

Characterizing Dissipative Elastic Metamaterials Produced by Additive Manufacturing

Viscoelastic behavior can be beneficial in enhancing the unprecedented dynamics of polymer metamaterials or, in contrast, negatively impacting their wave control mechanisms. It is, therefore, crucial to properly characterize the viscoelastic properties of a polymer metamaterial at its working frequencies to understand viscoelastic effects. However, the viscoelasticity of polymers is a complex phenomenon, and the data on storage and loss moduli at ultrasonic frequencies are extremely limited, especially for additively manufactured polymers. This work presents a protocol to experimentally characterize the viscoelastic properties of additively manufactured polymers and to use them in the numerical analysis of polymer metamaterials. Specifically, the protocol includes the description of the manufacturing process, experimental procedures to measure the thermal, viscoelastic, and mechanical properties of additively manufactured polymers, and an approach to use these properties in finite-element simulations of the metamaterial dynamics. The numerical results are validated in ultrasonic transmission tests. To exemplify the protocol, the analysis is focused on acrylonitrile butadiene styrene (ABS) and aims at characterizing the dynamic behavior of a simple metamaterial made from it by using fused deposition modeling (FDM) three-dimensional (3D) printing. The proposed protocol will be helpful for many researchers to estimate viscous losses in 3D-printed polymer elastic metamaterials that will improve the understanding of material-property relations for viscoelastic metamaterials and eventually stimulate the use of 3D-printed polymer metamaterial parts in various applications.

Additively manufactured polymers have been widely used for producing elastic metamaterials. The viscoelastic behavior of these polymers at ultrasonic frequencies remains, however, poorly studied. This study reports a protocol to estimate the viscoelastic properties of 3D-printed polymers and show how to use them to analyze the metamaterial dynamics.

Viscoelastic behavior can be beneficial in enhancing the unprecedented dynamics of polymer metamaterials or, in contrast, negatively impacting their wave ...

Determination of Photoreceptor Cell Spectral Sensitivity in an Insect Model from In Vivo Intracellular Recordings

Intracellular recording is a powerful technique used to determine how a single cell may respond to a given stimulus. In vision research, intracellular recording has historically been a common technique used to study sensitivities of individual photoreceptor cells to different light stimuli that is still being used today. However, there remains a dearth of detailed methodology in the literature for researchers wishing to replicate intracellular recording experiments in the eye. Here we present the insect as a model for examining eye physiology more generally. Insect photoreceptor cells are located near the surface of the eye and are therefore easy to reach, and many of the mechanisms involved in vision are conserved across animal phyla. We describe the basic procedure for in vivo intracellular recording of photoreceptor cells in the eye of a butterfly, with the goal of making this technique more accessible to researchers with little prior experience in electrophysiology. We introduce the basic equipment needed, how to prepare a live butterfly for recording, how to insert a glass microelectrode into a single cell, and finally the recording procedure itself. We also explain the basic analysis of raw response data for determining spectral sensitivity of individual cell types. Although our protocol focuses on determining spectral sensitivity, other stimuli (e.g., polarized light) and variations of the method are applicable to this setup.

Determination of Photoreceptor Cell Spectral Sensitivity in an Insect Model from In Vivo Intracellular Recordings

The electrophysiological technique of intracellular recording is demonstrated and used to determine spectral sensitivities of single photoreceptor cells in the compound eye of a butterfly.

Intracellular recording is a powerful technique used to determine how a single cell may respond to a given stimulus. In vision research, intracellular ...

Neuroscience

Studying Cavitation Enhanced Therapy

Interest in the therapeutic applications of ultrasound is significant and growing, with potential clinical targets ranging from cancer to Alzheimer&#8217;s disease. Cavitation - the formation and subsequent motion of bubbles within an ultrasound field - represents a key phenomenon underpinning many of these treatments. There remains, however, considerable uncertainty regarding the detailed mechanisms of action by which cavitation promotes therapeutic effects and there is a need to develop reliable monitoring techniques that can be implemented clinically. In particular, there is significant variation between studies in the exposure parameters reported as successfully delivering therapeutic effects and the corresponding acoustic emissions. The aim of this paper is to provide design guidelines and an experimental protocol using widely available components for performing studies of cavitation-mediated bioeffects, and&#160;include real-time acoustic monitoring. It is hoped that the protocol will enable more widespread incorporation of acoustic monitoring into therapeutic ultrasound experiments and facilitate easier comparison across studies of exposure conditions and their correlation to relevant bio-effects.

The presented experimental protocol can be used to perform real time measurements of cavitation activity in a cell culture device with the aim of enabling investigation of the conditions required for successful drug delivery and/or other bioeffects.

Interest in the therapeutic applications of ultrasound is significant and growing, with potential clinical targets ranging from cancer to ...

Evaluating MOF-Induced Cell Behavior Changes by Electric Cell-Substrate Sensing

Electric Cell-Substrate Sensing for Real-Time Evaluation of Metal-Organic Framework Toxicological Profiles

Metal-organic frameworks (MOFs) are hybrids formed through the coordination of metal ions and organic linkers in organic solvents. The implementation of MOFs in biomedical and industrial applications has led to concerns regarding their safety. Herein, the profile of a selected MOF, a zeolitic imidazole framework, was evaluated upon exposure to human lung epithelial cells. The platform for evaluation was a real-time technique (i.e., electric cell-substrate impedance sensing [ECIS]). This study identifies and discusses some of the deleterious effects of the selected MOF on the exposed cells. Furthermore, this study demonstrates the benefits of using the real-time method versus other biochemical assays for comprehensive cell evaluations. The study concludes that observed changes in cell behavior could hint at possible toxicity induced upon exposure&#160;to MOFs of different physicochemical characteristics and the dosage of those frameworks being used. By understanding changes in cell behavior, one foresees the ability to improve safe-by-design strategies of MOFs to be used for biomedical applications by specifically tailoring their physicochemical characteristics.

Author Spotlight: Advances in Evaluating Human Lung Epithelial Cells' Response to Metal-Organic Frameworks 

The following study evaluates the toxicological profile of a selected metal-organic framework utilizing electric cell-substrate impedance sensing (ECIS), a real-time, high-throughput screening technique.

Metal-organic frameworks (MOFs) are hybrids formed through the coordination of metal ions and organic linkers in organic solvents. The implementation of ...

Data Acquisition Protocol for Determining Embedded Sensitivity Functions

Podsumowanie

Przeglądaj więcej filmów

Rozdziały w tym wideo

Combining Multiple Data Acquisition Systems to Study Corticospinal Output and Multi-segment Biomechanics

Frequency Mixing Magnetic Detection Scanner for Imaging Magnetic Particles in Planar Samples

Drug-induced Sensitization of Adenylyl Cyclase: Assay Streamlining and Miniaturization for Small Molecule and siRNA Screening Applications

Electric Cell-substrate Impedance Sensing for the Quantification of Endothelial Proliferation, Barrier Function, and Motility

Effective Analysis of Human Exposure Conditions with Body-worn Dosimeters in the 2.4 GHz Band

Microfluidic Platform with Multiplexed Electronic Detection for Spatial Tracking of Particles

Characterizing Dissipative Elastic Metamaterials Produced by Additive Manufacturing

Determination of Photoreceptor Cell Spectral Sensitivity in an Insect Model from In Vivo Intracellular Recordings

Studying Cavitation Enhanced Therapy

Electric Cell-Substrate Sensing for Real-Time Evaluation of Metal-Organic Framework Toxicological Profiles